This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1652
Similar products
Front Hood Lift Supports Shocks Springs Props for Hummer H3 2006-2010
New
R737.00
Closed
11 May 24 00:20
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Buyer Protection
How you're covered
Get it now, pay later
Returns
Product information
Condition:
New
Location:
International
Bob Shop ID:
612435446
Front Hood Lift Supports Shocks Springs Props for Hummer H3 2006-2010
Features:
Easy to install.
YQ compression gas springs type, also known as free type gas spring, supporting bar, nitrogen spring is a high-pressure gas sealed in the cylinder, the piston produced by the elastic features of the product. The product does not need to work at the outside power, constant lifting force. Fully open the rear door is widely used in automobile, hood, back door luggage, mechanical equipment, construction machinery, furniture, fitness equipment, and other fields. It has a long life, easy to control, no maintenance and so on.
Specification:
Compressed Length: 15.8cm
Extended Length: 40cm
Suitable for For 2006-2010 Hummer H3
Installment:
1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed.
2. Before removing the old lift support, inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length.
3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8, then pull the support away from the vehicle and it will release.
4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur.
5. Lift Supports need to be installed fully extended. In most cases you just can't compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support.
6. If the ends are not lining up the support may need to be turned. To do this attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise unit the ends line up.
Package Included:
2 X Front Hood Gas Lift Supports
4 X Ball Screws
, 
, 
, 
, 
, 
, 
, 
, 
, 
Features:
Easy to install.
YQ compression gas springs type, also known as free type gas spring, supporting bar, nitrogen spring is a high-pressure gas sealed in the cylinder, the piston produced by the elastic features of the product. The product does not need to work at the outside power, constant lifting force. Fully open the rear door is widely used in automobile, hood, back door luggage, mechanical equipment, construction machinery, furniture, fitness equipment, and other fields. It has a long life, easy to control, no maintenance and so on.
Specification:
Compressed Length: 15.8cm
Extended Length: 40cm
Suitable for For 2006-2010 Hummer H3
Installment:
1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed.
2. Before removing the old lift support, inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length.
3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8, then pull the support away from the vehicle and it will release.
4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur.
5. Lift Supports need to be installed fully extended. In most cases you just can't compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support.
6. If the ends are not lining up the support may need to be turned. To do this attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise unit the ends line up.
Package Included:
2 X Front Hood Gas Lift Supports
4 X Ball Screws
, , , , , , , , ,