Quilting Walking Foot Sewing Machine Presser Foot Sewing Tool
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 12 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615193196
Quilting Walking Foot Sewing Machine Presser Foot Sewing Tool
Features:
To prevent slippage between the multilayer fabric, the cooperation of cloth feeding teeth on walking foot and needle plate ensure a better cloth feeding, to prevent a problem of short section of the lower multilayer fabric. Sewing surface seam line can get better results. It's also able to prevent wrinkling when sewing and hemming special cloth.
Material: Plastic and Steel
Size (Walking Foot): 7.8 x 2.5 x 1.6cm / 3.07 x 0.98 x 0.6 inch (L x W x H)
Size (Quilt Guide): 6.5 x 2.5 x 8cm / 2.55 x 0.98 x 3.14inch (L x W x H)
Usage:
Installation of walking foot:
First turn off the power switch
1. Raise the walking foot lever and needle
2. Loosen the walking foot fixing screws, remove the walking foot and walking foot holder
3. Install walking foot presser in foot pole. Synchronization presser foot lever must be put on mounting screws on the needle,tighten the screws.
Note: Sewing at low or medium speed.
Installation of quilting guide:
1. Put the quilting guide down into the slot behind the synchronization presser foot.
2. According to the desired width move the quilting guide.
Note:
1. Please allow 1-3mm error due to manual measurement, pls make sure you do not mind before you bid.
2. The colors may have different as the difference display, pls understand.
Package included:
1 x Quilting Walking Foot with Guide
Features:
To prevent slippage between the multilayer fabric, the cooperation of cloth feeding teeth on walking foot and needle plate ensure a better cloth feeding, to prevent a problem of short section of the lower multilayer fabric. Sewing surface seam line can get better results. It's also able to prevent wrinkling when sewing and hemming special cloth.
Material: Plastic and Steel
Size (Walking Foot): 7.8 x 2.5 x 1.6cm / 3.07 x 0.98 x 0.6 inch (L x W x H)
Size (Quilt Guide): 6.5 x 2.5 x 8cm / 2.55 x 0.98 x 3.14inch (L x W x H)
Usage:
Installation of walking foot:
First turn off the power switch
1. Raise the walking foot lever and needle
2. Loosen the walking foot fixing screws, remove the walking foot and walking foot holder
3. Install walking foot presser in foot pole. Synchronization presser foot lever must be put on mounting screws on the needle,tighten the screws.
Note: Sewing at low or medium speed.
Installation of quilting guide:
1. Put the quilting guide down into the slot behind the synchronization presser foot.
2. According to the desired width move the quilting guide.
Note:
1. Please allow 1-3mm error due to manual measurement, pls make sure you do not mind before you bid.
2. The colors may have different as the difference display, pls understand.
Package included:
1 x Quilting Walking Foot with Guide