Flipsky Dual FSESC6.6 ESC Based upon VESC6 W/ Aluminum Heatsink for Electric longboard RC Car
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 12 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615162467
Description:
Advanced Features: 1.Dual ESC can reach continuous 200A big current, give your board strong power 2.One PCBA board integrate two FSESC6 a??s function by internal CAN BUS circuit connection. 3.The mater and slave board connection can be switched On/Off 4.Preserve bluetooth module and RF module connections for both master and slave board 5.Aluminum anodized Heat sink with fins design for better heat dissipation 6.Compact size with heatsink: 120x91x20mm (L*W*D) 7.PCB layers: 8layers, thickness: 3oz/layer, total 24 oz thickness ? Spec:
??Product size:120x91x20mm (L*W*D)(Include Heatsink)
??Packaging size:110mm*135mm*200mm ?? Hardware: V 6.6 ??Firmware: VESC_default_no_hw_limits ??Voltage: 8V - 60V (Safe for 3S to 12S LiPo) for the dual ESC ??Voltage spikes may not exceed 60V ??Current: Continuous 100A single, total 200A , ?Instantaneous current 400A per single, total 800A for system instantaneous current. ??5V 1.5A output for external electronics for single ??3.3V 1A output for external electronics for single ??Modes: DC, BLDC, FOC (sinusoidal) ??Supported sensors: ABI, HALL, AS5047 ??6 shunts in dual system. Each is measurable for the current.
??For the manual,please click
??Fit for?electric longboard/RC Car/E-bike/E-scooter ? Other Features: ??Regenerative braking ??Traction control (single and dual settings) ??Sensor or sensorless operation ??Configurable RPM, Current, Voltage and Power Limits ??Input source: PPM, simulation, NRF Nyko Kama Nunchuck ??Communication ports: USB, CAN, UART, NRF, bluetooth ??Throttle curves and ramps for all input sources ??Separate acceleration and brake throttle curves ??Motor speed, ampere hours, watt hour count,Instant data analysis and reading via communication port ??Voltage and current protection setting for Motor and ESC
? Package?included:
1X Dual FSESC6.6+Heatsink 2X?VESC Sensor Wires 1X?Micro USB 1X?PPM cable soldered in Dual FSESC6.6 1X?Manual
Advanced Features: 1.Dual ESC can reach continuous 200A big current, give your board strong power 2.One PCBA board integrate two FSESC6 a??s function by internal CAN BUS circuit connection. 3.The mater and slave board connection can be switched On/Off 4.Preserve bluetooth module and RF module connections for both master and slave board 5.Aluminum anodized Heat sink with fins design for better heat dissipation 6.Compact size with heatsink: 120x91x20mm (L*W*D) 7.PCB layers: 8layers, thickness: 3oz/layer, total 24 oz thickness ? Spec:
??Product size:120x91x20mm (L*W*D)(Include Heatsink)
??Packaging size:110mm*135mm*200mm ?? Hardware: V 6.6 ??Firmware: VESC_default_no_hw_limits ??Voltage: 8V - 60V (Safe for 3S to 12S LiPo) for the dual ESC ??Voltage spikes may not exceed 60V ??Current: Continuous 100A single, total 200A , ?Instantaneous current 400A per single, total 800A for system instantaneous current. ??5V 1.5A output for external electronics for single ??3.3V 1A output for external electronics for single ??Modes: DC, BLDC, FOC (sinusoidal) ??Supported sensors: ABI, HALL, AS5047 ??6 shunts in dual system. Each is measurable for the current.
??For the manual,please click
??Fit for?electric longboard/RC Car/E-bike/E-scooter ? Other Features: ??Regenerative braking ??Traction control (single and dual settings) ??Sensor or sensorless operation ??Configurable RPM, Current, Voltage and Power Limits ??Input source: PPM, simulation, NRF Nyko Kama Nunchuck ??Communication ports: USB, CAN, UART, NRF, bluetooth ??Throttle curves and ramps for all input sources ??Separate acceleration and brake throttle curves ??Motor speed, ampere hours, watt hour count,Instant data analysis and reading via communication port ??Voltage and current protection setting for Motor and ESC
? Package?included:
1X Dual FSESC6.6+Heatsink 2X?VESC Sensor Wires 1X?Micro USB 1X?PPM cable soldered in Dual FSESC6.6 1X?Manual