WUPP ZH-983B6 Motorcycle Modified Intelligent Electric Heating Hand Cover Heated Grip
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Get it now, pay later
Seller
Product details
Condition
New
Location
International
Product code
EDA0018435
Bob Shop ID
613683170
Description
1. Material: nitrile
2. Handle length: left handle: 143x36mm; right handle: 127x36mm
3. Suitable pipe diameter: 22mm
4. Input voltage: DC12V
5. Product power: red light 35W, blue light 25W, green light 17W
6. Handle temperature: low temperature 40 degrees Celsius, medium temperature 50 degrees Celsius, high temperature 60 degrees Celsius
7. Switch type: multi-stage adjustable temperature control switch
8. Applicable models: 12V motorcycle with a handlebar diameter of 22mm
9. Product accessories: 3M glue x1, rear-view mirror fixing bracket x1
10. One-piece molding to prevent rain and dust from entering the internal corrosion parts, longer service life and safer
11. Built-in intelligent temperature control chip, three-speed adjustable temperature, intelligent temperature control is safer
12. Double throttle cable buckle, wider installation range
13. The design can be sealed and can be opened, which will not affect the installation of the handle outside the handle, and only the lights and other decorative accessories can be used, which is more beautiful and convenient
14. The product has added a standby mode. After switching to the standby state, the electric heating handle will automatically maintain a constant temperature of about 50 degrees, and it will automatically shut down after two hours. There is no need to worry about running out of the battery of the motorcycle because of forgetting to turn off the switch.
Installation notes:
1. Remove the original handlebar
2. Use the left hand to moisten the inner hole with soapy water, and the twist should not be too large during installation
3. When installing the balance iron on the left hand handle, adjust the position of the balance iron to be slightly separated from the handle, and do not squeeze the handle when tightening the screw
4. If you use the left handle to slide on a steel pipe, remove the balance iron and fix it with a few drops of 502 glue from the end of the handle
5. The power cord, the red wire is connected to the positive pole, and the black wire is connected to the negative pole, please confirm before connecting it, and do not reverse the connection
6. When installing the left-hand handle, the power cord should be left enough for rotation
7. Put the switch L-shaped bracket on the rearview mirror, fix it to the rearview mirror base, and tighten it.
Precautions:
1. When installing the left handle, do not twist the handle too much. Excessive twisting will cause the heating wire to shift.
2. For models with balance iron, please adjust the installation position of the balance iron. Do not squeeze the handle when tightening the screws. The balance iron is slightly separated from the handle. If the installation position of the balance iron cannot be adjusted, please add a spacer between the balance iron and the handle. Excessive squeezing of the handle may cause difficulty in turning the handle switch and abnormal damage such as the heating wire squeezing out of the handle surface.
2. Handle length: left handle: 143x36mm; right handle: 127x36mm
3. Suitable pipe diameter: 22mm
4. Input voltage: DC12V
5. Product power: red light 35W, blue light 25W, green light 17W
6. Handle temperature: low temperature 40 degrees Celsius, medium temperature 50 degrees Celsius, high temperature 60 degrees Celsius
7. Switch type: multi-stage adjustable temperature control switch
8. Applicable models: 12V motorcycle with a handlebar diameter of 22mm
9. Product accessories: 3M glue x1, rear-view mirror fixing bracket x1
10. One-piece molding to prevent rain and dust from entering the internal corrosion parts, longer service life and safer
11. Built-in intelligent temperature control chip, three-speed adjustable temperature, intelligent temperature control is safer
12. Double throttle cable buckle, wider installation range
13. The design can be sealed and can be opened, which will not affect the installation of the handle outside the handle, and only the lights and other decorative accessories can be used, which is more beautiful and convenient
14. The product has added a standby mode. After switching to the standby state, the electric heating handle will automatically maintain a constant temperature of about 50 degrees, and it will automatically shut down after two hours. There is no need to worry about running out of the battery of the motorcycle because of forgetting to turn off the switch.
Installation notes:
1. Remove the original handlebar
2. Use the left hand to moisten the inner hole with soapy water, and the twist should not be too large during installation
3. When installing the balance iron on the left hand handle, adjust the position of the balance iron to be slightly separated from the handle, and do not squeeze the handle when tightening the screw
4. If you use the left handle to slide on a steel pipe, remove the balance iron and fix it with a few drops of 502 glue from the end of the handle
5. The power cord, the red wire is connected to the positive pole, and the black wire is connected to the negative pole, please confirm before connecting it, and do not reverse the connection
6. When installing the left-hand handle, the power cord should be left enough for rotation
7. Put the switch L-shaped bracket on the rearview mirror, fix it to the rearview mirror base, and tighten it.
Precautions:
1. When installing the left handle, do not twist the handle too much. Excessive twisting will cause the heating wire to shift.
2. For models with balance iron, please adjust the installation position of the balance iron. Do not squeeze the handle when tightening the screws. The balance iron is slightly separated from the handle. If the installation position of the balance iron cannot be adjusted, please add a spacer between the balance iron and the handle. Excessive squeezing of the handle may cause difficulty in turning the handle switch and abnormal damage such as the heating wire squeezing out of the handle surface.
Specification:
| Package Weight |
|
OEM/ODM are Welcome! we can print customised artwork and logo