This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1923
Similar products
DIY PCB Circuit Board 5MOS Welding Equipment Portable 12V Battery Storage Spot Welding Machine with
New
R615.00
Closed
9 Jun 24 23:04
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 12 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615103753
Description:
Lithium battery, advantages: portable, stable and reliable, and durable.
Users need to supply 12V battery power, welding current is about 90A ~ 150A, for the common 18650/26650/32650 0.1mm ~ 0.15mm nickel plated welding. After several generations of product updates, it is now upgraded to automatically trigger the welding, liberating the buttons of the fingers.
Switch function: press the switch for 1.5 seconds to switch (blue light: low power, green light: medium power, red light: high power)
Power supply requirements:
System voltage: 12V-14.6V (It will stop???12V)
Current requirements: 150A or more instantaneous output (such as car starter power supply, 3S RC high-power battery pack, 20A lead-acid battery with good performance above 20A)
Misunderstanding: Don`t think that you can use 3 series 18650 series to supply power. After all, the conventional 18650 only has 3-5C discharge rate, so each section can only provide 2.5A*3=7.5A load capacity, which is far from 150A unless 20 Parallel connection, 3 series and 60 sections of 18650 are possible, but it is obviously unrealistic.
Features:
1. it is equipped with a 3.7-4.2V 4.5ah power lithium battery with a discharge rate of 100C and a load capacity of about 400A. 2. Through the MOS tube output, this energy will be concentrated at the end of the welding pen, and it will be heated by short circuit. 3. Fuse the nickel sheet firmly with the battery. All this will happen in milliseconds,And it is precisely controlled by the single-chip microcomputer program without trigger switch. 4. Free your fingers or foot pedals completely. 5. Comes with a charging control module, which charges the battery through the USB port, and is charged with hundreds of welding points on commonly used nickel-plated sheets within 0.1mm-0.15mm. ? Battery recommendation: ? (1) 20-45ah Lead-acid battery with good performance and small internal resistance (2) 3.5-5.5ah 45C 3S aeromodel lithium battery pack (3) 30-35ah capacity 18650 battery pack
Package Included:
1 x Main Board 2 x 10AWG Input Wires 2 x Spot Soldering Pens ?
Lithium battery, advantages: portable, stable and reliable, and durable.
Users need to supply 12V battery power, welding current is about 90A ~ 150A, for the common 18650/26650/32650 0.1mm ~ 0.15mm nickel plated welding. After several generations of product updates, it is now upgraded to automatically trigger the welding, liberating the buttons of the fingers.
Switch function: press the switch for 1.5 seconds to switch (blue light: low power, green light: medium power, red light: high power)
Power supply requirements:
System voltage: 12V-14.6V (It will stop???12V)
Current requirements: 150A or more instantaneous output (such as car starter power supply, 3S RC high-power battery pack, 20A lead-acid battery with good performance above 20A)
Misunderstanding: Don`t think that you can use 3 series 18650 series to supply power. After all, the conventional 18650 only has 3-5C discharge rate, so each section can only provide 2.5A*3=7.5A load capacity, which is far from 150A unless 20 Parallel connection, 3 series and 60 sections of 18650 are possible, but it is obviously unrealistic.
Features:
1. it is equipped with a 3.7-4.2V 4.5ah power lithium battery with a discharge rate of 100C and a load capacity of about 400A. 2. Through the MOS tube output, this energy will be concentrated at the end of the welding pen, and it will be heated by short circuit. 3. Fuse the nickel sheet firmly with the battery. All this will happen in milliseconds,And it is precisely controlled by the single-chip microcomputer program without trigger switch. 4. Free your fingers or foot pedals completely. 5. Comes with a charging control module, which charges the battery through the USB port, and is charged with hundreds of welding points on commonly used nickel-plated sheets within 0.1mm-0.15mm. ? Battery recommendation: ? (1) 20-45ah Lead-acid battery with good performance and small internal resistance (2) 3.5-5.5ah 45C 3S aeromodel lithium battery pack (3) 30-35ah capacity 18650 battery pack
Package Included:
1 x Main Board 2 x 10AWG Input Wires 2 x Spot Soldering Pens ?
