This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1900
Automatic Irrigation Module DIY Set for Soil Moisture Detection and Automatic Water Pumping
New
R356.00
Closed
9 Jun 24 23:05
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 12 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615104432
.size_table_start table,.size_table_start table tr td { border:2px solid #ddd;}.size_table_start table { width: 100%; min-height: 25px; line-height: 25px; text-align: center; border-collapse: collapse;}.size_table_start,.size_table_end {clear:both;}
Overview:
This product does not need programming,? not include the microcontroller, so we don`t provide any code.? We don`t provide power, you can use the charging treasure (5V DC) as a power supply, or use 4 AA batteries.?
About Testing:
1. Test the relay module: connect the relay module VCC to 5V, GND to the ground, and IN to GND, the relay is will beat, if IN is vacant, the relay will restored, so you can hear the a??Kakaa?? sound; ?2. Test the soil moisture sensor module: connect the fork probe and transmitter module with two dupont cable, connect the transmitter module VCC to 5V, and GND to the ground. The red power lamp is always on as soon as it is powered on, and the green (blue) led will gleam for once; put the fork probe directly into the water, the green (blue) light will on; ?3. Connect the red line of the pump to 5V, black wire to the ground, the water pump will start work. Note that: the test can be performed for 1 second. because it can not expose to the air for a long time. ?4. According to the schematic assembly.
Note:?
1. This product needn`t welding, but it requires you to strip the wire, twist the copper wire together and protect it with black tape.? 2. The pump can not run a long time in the air;? 3. Connect the system and power, the pump will work all time, it is right, because in the air, the probe can not detect the humidity, if install it to the flowerpot, then it can normally work. Note: Do not pour water directly onto the soil probe. If the humidity of the water is too high, it will cause the product to rust and become inoperable. 4. Pump without power supply, power supply matched to the other, and water pump is a dc pumps, pump voltage 3 v, with DC3 - use 6 v power supply. (cannot be used directly with 220 v ac voltage)
Pump:
DC Voltage: 2.5-6V Working current: 130-220mA Power: 0.4-1.5W Maximum lift: 40-110cm / 15.75-43.4 Flow rate: 80-120L/H Outside diameter of water outlet: approx. 7.5mm / 0.3 Inside diameter of water outlet: approx. 4.7mm / 0.18 Diameter: approx. 24mm / 0.95 Length: approx. 45mm / 1.8 Height: approx. 33mm / 1.30 Wire length: about 15-20cm (red: + , black(white): - ) Material: engineering plastic Driving mode: brushless DC design, magnetic driving Continuous working life of 500 hours
Package Included:
1 x L9110S Controller Board 1 x Soil Moisture Probe + Comparison Module 1 x Small Pump 1 x Battery Holder 1 x 50cm Silicone Tube
This product does not need programming,? not include the microcontroller, so we don`t provide any code.? We don`t provide power, you can use the charging treasure (5V DC) as a power supply, or use 4 AA batteries.?
About Testing:
1. Test the relay module: connect the relay module VCC to 5V, GND to the ground, and IN to GND, the relay is will beat, if IN is vacant, the relay will restored, so you can hear the a??Kakaa?? sound; ?2. Test the soil moisture sensor module: connect the fork probe and transmitter module with two dupont cable, connect the transmitter module VCC to 5V, and GND to the ground. The red power lamp is always on as soon as it is powered on, and the green (blue) led will gleam for once; put the fork probe directly into the water, the green (blue) light will on; ?3. Connect the red line of the pump to 5V, black wire to the ground, the water pump will start work. Note that: the test can be performed for 1 second. because it can not expose to the air for a long time. ?4. According to the schematic assembly.
Note:?
1. This product needn`t welding, but it requires you to strip the wire, twist the copper wire together and protect it with black tape.? 2. The pump can not run a long time in the air;? 3. Connect the system and power, the pump will work all time, it is right, because in the air, the probe can not detect the humidity, if install it to the flowerpot, then it can normally work. Note: Do not pour water directly onto the soil probe. If the humidity of the water is too high, it will cause the product to rust and become inoperable. 4. Pump without power supply, power supply matched to the other, and water pump is a dc pumps, pump voltage 3 v, with DC3 - use 6 v power supply. (cannot be used directly with 220 v ac voltage)
Pump:
DC Voltage: 2.5-6V Working current: 130-220mA Power: 0.4-1.5W Maximum lift: 40-110cm / 15.75-43.4 Flow rate: 80-120L/H Outside diameter of water outlet: approx. 7.5mm / 0.3 Inside diameter of water outlet: approx. 4.7mm / 0.18 Diameter: approx. 24mm / 0.95 Length: approx. 45mm / 1.8 Height: approx. 33mm / 1.30 Wire length: about 15-20cm (red: + , black(white): - ) Material: engineering plastic Driving mode: brushless DC design, magnetic driving Continuous working life of 500 hours
Package Included:
1 x L9110S Controller Board 1 x Soil Moisture Probe + Comparison Module 1 x Small Pump 1 x Battery Holder 1 x 50cm Silicone Tube
