Corona R4DM-SB 2.4G 4CH DMSS Compatible Receiver With S.Bus
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615150735
Corona R4DM-SB 2.4G 4CH DMSS Compatible Receiver With S.Bus
Description:
The Corona R4DM-SB is a 2.4GHz DMSS compatible receiver that is designed to use with JR DMSS 2.4GHz transmitters, such as XG6,XG7,XG8 ,XG11 and XG14 under DMSS protocol mode.
Specification:
Brand Name: Corona
Item Name: R4DM-SB
Channels: 4
Modulation: DMSS
Band: 2.4GHz
Weight: 7g
Voltage Range: 3.6 ~ 8.5V
Operating Current: 60mA max, 35mA under load
Operating Temperature: -10~70 degrees C
Latency: 13 ~ 14ms
Sensitivity: -96dBm
Features:
Full range receiver
4 Channels - throttle, aileron, rudder, elevator
Supports S.BUS connectivity
For use with JR DMSS transmitters
Lightweight and compact weighing in at just 7 grams
Fail safe programmable
Bind Procedure:
Turn on the DMSS transmitter, leave it 0.5M~1M away the receiver.
Connect a shorter on CH2 of R4DM(signal and GND) when bind with XG7; and connect a shorter on CH3 of R4DM when bind with other transmitters.
Connect the battery to the receiver(CH1 or CH4 of R4DM) while pressing down receivera??s button.
Red LED light on and Green LED off when searching signals, and turn to Green LED light on and Red LED off indicate bind is succeeded.
Fail-safe Setting:
R4DM set failsafe on the DMSS transmitter just like the operation of the JRa??s DMSS receivers. We highly recommend you set failsafe feature while flying your models. An example of a useful Failsafe setting would be to shut down the modela??s throttle, so that it does not fly or drive away uncontrolled.
Special/Normal Mode Switch Guide:
?? If your receiver has been linked with your transmitter, please power off your transmitter. When your receivera??s LED light red, push down and hold the button on your receiver for more than 6 seconds and not more than 10 seconds, release the button to see the green led flash, push down the button again right now, receiver get back to light red. Now the MODE status has changed between Special mode and Normal mode. When green led flash low indicate normal mode to special mode, and green led flash fast indicate special mode to normal mode.
?? Under the special mode status, you can get S.BUS output feature on the last servo channel, other channels not changed.
NOTE: If you want to reset the receiver to normal mode, you can rebind the receiver to your transmitter.?
LED Status:
Red LED on,Green LED off, No signal searched
Red LED off,Green LED solid,Signal is very good
Red LED off,Green LED flash,Signal is not very good
Red LED off,Green LED off-flash,Signal is weak
Package Included:
1x?Corona R4DM-SB receiver
Description:
The Corona R4DM-SB is a 2.4GHz DMSS compatible receiver that is designed to use with JR DMSS 2.4GHz transmitters, such as XG6,XG7,XG8 ,XG11 and XG14 under DMSS protocol mode.
Specification:
Brand Name: Corona
Item Name: R4DM-SB
Channels: 4
Modulation: DMSS
Band: 2.4GHz
Weight: 7g
Voltage Range: 3.6 ~ 8.5V
Operating Current: 60mA max, 35mA under load
Operating Temperature: -10~70 degrees C
Latency: 13 ~ 14ms
Sensitivity: -96dBm
Features:
Full range receiver
4 Channels - throttle, aileron, rudder, elevator
Supports S.BUS connectivity
For use with JR DMSS transmitters
Lightweight and compact weighing in at just 7 grams
Fail safe programmable
Bind Procedure:
Turn on the DMSS transmitter, leave it 0.5M~1M away the receiver.
Connect a shorter on CH2 of R4DM(signal and GND) when bind with XG7; and connect a shorter on CH3 of R4DM when bind with other transmitters.
Connect the battery to the receiver(CH1 or CH4 of R4DM) while pressing down receivera??s button.
Red LED light on and Green LED off when searching signals, and turn to Green LED light on and Red LED off indicate bind is succeeded.
Fail-safe Setting:
R4DM set failsafe on the DMSS transmitter just like the operation of the JRa??s DMSS receivers. We highly recommend you set failsafe feature while flying your models. An example of a useful Failsafe setting would be to shut down the modela??s throttle, so that it does not fly or drive away uncontrolled.
Special/Normal Mode Switch Guide:
?? If your receiver has been linked with your transmitter, please power off your transmitter. When your receivera??s LED light red, push down and hold the button on your receiver for more than 6 seconds and not more than 10 seconds, release the button to see the green led flash, push down the button again right now, receiver get back to light red. Now the MODE status has changed between Special mode and Normal mode. When green led flash low indicate normal mode to special mode, and green led flash fast indicate special mode to normal mode.
?? Under the special mode status, you can get S.BUS output feature on the last servo channel, other channels not changed.
NOTE: If you want to reset the receiver to normal mode, you can rebind the receiver to your transmitter.?
LED Status:
Red LED on,Green LED off, No signal searched
Red LED off,Green LED solid,Signal is very good
Red LED off,Green LED flash,Signal is not very good
Red LED off,Green LED off-flash,Signal is weak
Package Included:
1x?Corona R4DM-SB receiver