KSGER T12 Soldering Station STM32 Digital Controller ABS Case 907 Soldering Iron Handle Auto-sleep B
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615185649
Specification:
Input Voltage: AC110-240V Power Supply: 24V 5A Temperature Range: 40-500a?? Tin Melting Time: <8s Output Power: 72W Auto Sleep: Yes Boost Function: Yes Controller: STM32 Digital Size: 150 x 88 x 38mm Case Material: ABS Plastic
? Operation Instructions: ? 1. There are 4 working modes: Boost mode, working mode, sleep mode, and shutdown mode. 2. Short press to enter the Boost mode, Boost temperature and Boost time can be set, Boost temperature setting 5-100 degrees, Boost setting 1-30 minutes 3. Working mode, the working temperature range is 40-500 degrees, the maximum temperature is limited to 550 degrees, and the default is 300 degrees. 4. In sleep mode, double-click to enter, sleep time is set to 0-60 minutes, and sleep temperature is set to 40-300 degrees. 5. In the shutdown mode, the combo is turned off three times, the detection time is 0-60 minutes, and the heater stops heating after the shutdown mode is started.
Menu?(press and hold the encoder for 3 seconds to be into the menu): P-0? Boost temperature setting (default 50 degrees) P-1? Boost time setting (default 5 minutes) P-2? Sleep temperature setting (default 200 degrees) P-3? Sleep time setting (default 10 minutes) P-4? shutdown time setting (default 30 minutes) P-5? temperature calibration, linear calibration parameters, divided into three points 400, 330, 260 degrees? P-6? Restore default settings, 0 cancel, 1 OK. ? Work Description: ? If No T12 Handle or NO T12 tip is inserted into the soldering station or the T12 tip is bad. But, after the heating program is turned on, the temperature of the T12 tip is not raised ,display will show ERR. Display will show temperature if working well. The first decimal point of the digital tube is always on when in a??Boost? modea??, and the last decimal point is always on when in a??Sleep modea?? , the shutdown status showsa?? ---a??. In sleep mode, you can short-press the encoder or detect the vibration switch to wake up to normal operation. The shutdown mode can only be awakened by a short press of the button. ? Buzzer Description: ? When the set temperature is reached, the buzzer will sound a short sound. When entering the boost mode, it will sound for a long time. When entering the sleep mode, it will prompt one long and two short, and enter the shutdown prompt for one long and three short.
Package Included:
1 x?KSGER T12 Soldering Station
1 x 907 Soldering Handle
1 x T12-K Tip
Detail Pictures: ?
Input Voltage: AC110-240V Power Supply: 24V 5A Temperature Range: 40-500a?? Tin Melting Time: <8s Output Power: 72W Auto Sleep: Yes Boost Function: Yes Controller: STM32 Digital Size: 150 x 88 x 38mm Case Material: ABS Plastic
? Operation Instructions: ? 1. There are 4 working modes: Boost mode, working mode, sleep mode, and shutdown mode. 2. Short press to enter the Boost mode, Boost temperature and Boost time can be set, Boost temperature setting 5-100 degrees, Boost setting 1-30 minutes 3. Working mode, the working temperature range is 40-500 degrees, the maximum temperature is limited to 550 degrees, and the default is 300 degrees. 4. In sleep mode, double-click to enter, sleep time is set to 0-60 minutes, and sleep temperature is set to 40-300 degrees. 5. In the shutdown mode, the combo is turned off three times, the detection time is 0-60 minutes, and the heater stops heating after the shutdown mode is started.
Menu?(press and hold the encoder for 3 seconds to be into the menu): P-0? Boost temperature setting (default 50 degrees) P-1? Boost time setting (default 5 minutes) P-2? Sleep temperature setting (default 200 degrees) P-3? Sleep time setting (default 10 minutes) P-4? shutdown time setting (default 30 minutes) P-5? temperature calibration, linear calibration parameters, divided into three points 400, 330, 260 degrees? P-6? Restore default settings, 0 cancel, 1 OK. ? Work Description: ? If No T12 Handle or NO T12 tip is inserted into the soldering station or the T12 tip is bad. But, after the heating program is turned on, the temperature of the T12 tip is not raised ,display will show ERR. Display will show temperature if working well. The first decimal point of the digital tube is always on when in a??Boost? modea??, and the last decimal point is always on when in a??Sleep modea?? , the shutdown status showsa?? ---a??. In sleep mode, you can short-press the encoder or detect the vibration switch to wake up to normal operation. The shutdown mode can only be awakened by a short press of the button. ? Buzzer Description: ? When the set temperature is reached, the buzzer will sound a short sound. When entering the boost mode, it will sound for a long time. When entering the sleep mode, it will prompt one long and two short, and enter the shutdown prompt for one long and three short.
Package Included:
1 x?KSGER T12 Soldering Station
1 x 907 Soldering Handle
1 x T12-K Tip
Detail Pictures: ?