NitroOBD2 Plug and Drive Performance Tuning Box, More power/torque, PETROL CARS, LOCAL STOCK

For PETROL Cars

 

Upto 35% more power

 

Upto 25% more torque

 

LOCAL STOCK

 

 

 

R225 each

 

 

Countrywide Post

 

 

NitroOBD2 is a Plug & Drive Ready device to function the increasing the performance of engine. NitroOBD2 is easy to install. Just plug it into the OBD2 connector of cars. NitroOBD2 fits all car from the year of 1996. It works based OBD2 protocols as remaping the Car's computer ECU. After driving 200 km road total, NitroOBD2 adjusts itself to the car, according to the drivers' habits and always keeps remaping the ECU to increase the performance of engine.

 

 

What does it do?

 

According to your driving habits, NitroOBD2 makes new map in the car's computer ECU to increase the performance of your car. As you driving much more KM/Mile, it renews the map. Thus it keeps the vehicle's power and torque increasing.

 

 

What is NitroOBD2 Chip Tuning Box?

 

NitroOBD2 is a Chip Tuning Box which can be plugged into OBD2 connector of your car to increase the performance of your car. When it plugged into OBD2 connector, NitroOBD2 receives the information from the car computer ECU. With the received data from ECU, NitroOBD2 adjusts the boost pressure, quantity of fuel, injection timing and pressure to increase the performance of your car. NitroOBD2 Chip Tuning Box does not exceed the manufacturer requirements. It works only within the tolerance of the engine. NitroOBD2 finds out the hidden power of your car. NitroOBD2 does not damage the engine and the car computer ECU or not cause any negative effects to the car factory setting. NitroOBD2 does not change any of the settings permanently. To turn back to the car's original settings, just unplug NitroOBD2 from OBD2 connector.NitroOBD2 finds out the hidden power of your car.

 

 

Features:

 

1.Up to 35% more power 

2.Up to 25 % more torque

3.NitroOBD2 is very easy to use

4.Plug NitroOBD2 into OBD2 connector of your car. And turn the ignition on for 30 seconds. And Turn the engine on

5.NitroOBD2 settings are optimal and the best for your car. Even the parameters are different for each vehicle, there might not be a need to make an additional adjustment

 

NitroOBD2 works on the basis of changing the signal form ECU. As a consequence, it changes the whole injection map. The main difference between NitroOBD2 Chip Tuning Box and Remapping tuning methods is that NitroOBD2 Chip Tuning Box is easily removable, and after unplug you go back to the factory settings. NitroOBD2 is the cheap and safe type of tuning. Remapping is a permanent change to your car. This is the expensive tuning and you cannot remove it. NitroOBD2 is equipped with the engine protection function and 100% safe for your car engine. NitroOBD2 produced on the printed circuit board in SMD technology. NitroOBD2 Chip Tuning Boxes are high quality.

 

 

Installation and Calibration:

 

1. Pull the Car Key out from the ignition

 

2. Find OBD2 connector(*) in your car and Plug in NitroOBD2

 

3. Insert the key into the ignition and twist the key to the first stage. (Do not start the car)

 

4. Press the reset buttom for about 5 sec. After releasing the buttom, just wait for a while about 30-54 sec. (NitroOBD2 will communicate and establish connection with ECU)

 

5. Start up the engine

 

6. NitroOBD2 will recognize your vehicle and your driving habits, after around 200 km/150 miles driving and thus NitroOBD2 will adjust itself to match your car perfectly for more fuel saving

 

 

CE / FCC / RoHS

 

 

Package contents:

 

1.NitroOBD2 Chip Tuning Box Interface

2.User Manual English