Waveshare 2.9 Inch ink Screen 2.9inch Flexible E-Ink Display HAT 296128 Resolution Black and Whi
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615101048
Documents:
Overview:
This is a flexible E-Ink display HAT, 2.9inch, 296??128 resolution, with embedded controller, communicating via SPI interface, supports partial refresh. Compared with normal e-Paper panels, this flexible panel allows bending without being damaged. Combined with the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications where curved surface display is required, such as industrial instruments, smart wearable-devices, and so on.
Features:
Flexible e-Paper, the display section is bendable (DON`T bend the FPC section) No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano Preserved solder pads for SPI interface, for connecting with other controller boards like Arduino/Nucleo, etc.
Specifications:
Operating voltage: 3.3V Interface: 3-wire SPI, 4-wire SPI Outline dimension: 79mm ?? 36.7mm ?? 0.34mm Display size: 66.9mm ?? 29.06mm Dot pitch: 0.227 ?? 0.226 Resolution: 296 ?? 128 Display color: black, white Grey level: 2 Full refresh time: 2s Refresh power: 26.4mW(typ.) Standby power: <0.017mW Viewing angle: >170?ﾣ
Interface:
Package includes:
1 x?2.9inch e-Paper HAT (D)?
Overview:
This is a flexible E-Ink display HAT, 2.9inch, 296??128 resolution, with embedded controller, communicating via SPI interface, supports partial refresh. Compared with normal e-Paper panels, this flexible panel allows bending without being damaged. Combined with the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications where curved surface display is required, such as industrial instruments, smart wearable-devices, and so on.
Features:
Flexible e-Paper, the display section is bendable (DON`T bend the FPC section) No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano Preserved solder pads for SPI interface, for connecting with other controller boards like Arduino/Nucleo, etc.
Specifications:
Operating voltage: 3.3V Interface: 3-wire SPI, 4-wire SPI Outline dimension: 79mm ?? 36.7mm ?? 0.34mm Display size: 66.9mm ?? 29.06mm Dot pitch: 0.227 ?? 0.226 Resolution: 296 ?? 128 Display color: black, white Grey level: 2 Full refresh time: 2s Refresh power: 26.4mW(typ.) Standby power: <0.017mW Viewing angle: >170?ﾣ
Interface:
| SYMBOL | DESCRIPTION |
| VCC | 3.3V / 5V |
| GND | Ground |
| NC | NC |
| DIN | SPI MOSI pin |
| CLK | SPI SCK pin |
| CS | SPI chip selection, low active |
| DC | Data/Command selection (high for data, low for command) |
| RST | External reset, low active |
| BUSY | Busy status output, low active |
Package includes:
1 x?2.9inch e-Paper HAT (D)?
