This item has closed with no items sold
Similar products
CS-054B1 Third Generation Motorcycle Modified Electric Heating Hand Cover Heated Grip Handlebar
New
R266.00
Closed
6 May 24 02:44
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Buyer Protection
How you're covered
Get it now, pay later
Product information
Condition:
New
Location:
International
Product code:
MOTA5901
Bob Shop ID:
613290964
1. Adopt a simple modification method, that is, non-destructive appearance, easy to operate and easy to install.
2. Using PET metal heating film, the heating speed is very fast, several seconds fast, safe and fast.
3. Use ship type switch, waterproof, dustproof, beautiful and safe.
4. Switch design, can be directly installed on the mirror seat of rearview mirror, without drilling, without destroying, very simple.
5. DC 12V input, suitable for all motorcycles, very wide range of use
6. Input voltage: 12V
7. Product power: 10W (power on one side) 20W on both sides
8. Handle temperature: low temperature: 30 Celsius degree, high temperature 50-60 Celsius degree
9. Switch type: waterproof, waterproof and dust switch for ship type
10. Product accessories: one pair of heat-shrinkable sleeves, one pair of waterproof insulating tape, one pair of instructions
11. Net weight: 75g
12. Size: 9.5x8cm
Installation method:
1. Put the heater on the handlebar and adjust it to the right position.
2. Use tape to fix (wrap) the heater evenly on the handlebars, especially at the junction of the heater.
3. Put on the casing, adjust the position, and use the hot air gun (or lighter or blower) to blow the two folds of the casing longitudinally and symmetrically until the contraction is uniform, then blow the other parts evenly until the contraction of each part of the casing is uniform and even.
4. The switch is installed under the mirror pole of the rearview mirror.
5. Connect the power cord, red and black wires are positive and negative, but must be connected to the lower pole output line of the door lock (where the key is inserted).
2. Using PET metal heating film, the heating speed is very fast, several seconds fast, safe and fast.
3. Use ship type switch, waterproof, dustproof, beautiful and safe.
4. Switch design, can be directly installed on the mirror seat of rearview mirror, without drilling, without destroying, very simple.
5. DC 12V input, suitable for all motorcycles, very wide range of use
6. Input voltage: 12V
7. Product power: 10W (power on one side) 20W on both sides
8. Handle temperature: low temperature: 30 Celsius degree, high temperature 50-60 Celsius degree
9. Switch type: waterproof, waterproof and dust switch for ship type
10. Product accessories: one pair of heat-shrinkable sleeves, one pair of waterproof insulating tape, one pair of instructions
11. Net weight: 75g
12. Size: 9.5x8cm
Installation method:
1. Put the heater on the handlebar and adjust it to the right position.
2. Use tape to fix (wrap) the heater evenly on the handlebars, especially at the junction of the heater.
3. Put on the casing, adjust the position, and use the hot air gun (or lighter or blower) to blow the two folds of the casing longitudinally and symmetrically until the contraction is uniform, then blow the other parts evenly until the contraction of each part of the casing is uniform and even.
4. The switch is installed under the mirror pole of the rearview mirror.
5. Connect the power cord, red and black wires are positive and negative, but must be connected to the lower pole output line of the door lock (where the key is inserted).