This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1571
Similar products
Weighing Transmitter Weighing Amplifier Weight Sensor Voltage Current Converter DC 12-24V 4-20MA Loa
New
R637.00
Closed
11 Apr 24 01:04
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Buyer Protection
How you're covered
Get it now, pay later
Returns
Product information
Condition:
New
Location:
International
Bob Shop ID:
609785221
.size_table_start table,.size_table_start table tr td { border:2px solid #ddd;}.size_table_start table { width: 100%; min-height: 25px; line-height: 25px; text-align: center; border-collapse: collapse;}.size_table_start,.size_table_end {clear:both;}
Description: ? Housing and wire connectors are waterproof design, good sealing, suitable for harsh environments Look beautiful, durable, anti-jamming performance Ultra- high-precision op-amp circuit, high accuracy, good stability The power supply has reverse polarity protection, surge protection, overcurrent protection Suitable for weighing, pull pressure, torque, and other strain sensors.
Technical Parameters:? ? Working voltage: DC 12-24V Output signal: voltage (0-5V, 0-10V, 1-5V, ± 5V) 4-20ma input signal: sensor sensitivity 2.0MV/V output incentive: 5V(E+) Operating temperature range: -20 - 80?ﾣC Operating Humidity: 10% RH-90% RH (non-condensing) Accuracy: better than 0.1% F.S Precision: better than 0.05% F.S Gear selection: dial switch turn OFF, V0 output 0-5v, 1 turn to ON V0 output 0-10V, 1 and 2 both turn to OFF, VO output 0-5v, IO output 4-20MA .
About debugging: ? 1 zero adjustment First of all, make the system is in the idle state, adjust the marking ZERO potentiometer to adjust the zero offset. The multimeter is used to measure the output voltage or current, let show value as close as possible to the zero value display. Or change the magnification zero change will become big. 2 gain adjustment The system loading a certain weight value (the recommended range: 80% ~ 100% FS), the calculation of the output current value according to the load weight and the maximum weighting value relation, using the digital multimeter monitoring output, potentiometer to adjust amplifier gain spin-labeled SPAN. 3 the retest The system is in the idle state, measuring the zero output; loading a certain weight value, output voltage measurement whether fluoride expectation magnification If not, repeat steps 1, 2 adjust again.
Package includes:? ? 1 x Load Cell sensor Amplifier Transmitter?
Technical Parameters:? ? Working voltage: DC 12-24V Output signal: voltage (0-5V, 0-10V, 1-5V, ± 5V) 4-20ma input signal: sensor sensitivity 2.0MV/V output incentive: 5V(E+) Operating temperature range: -20 - 80?ﾣC Operating Humidity: 10% RH-90% RH (non-condensing) Accuracy: better than 0.1% F.S Precision: better than 0.05% F.S Gear selection: dial switch turn OFF, V0 output 0-5v, 1 turn to ON V0 output 0-10V, 1 and 2 both turn to OFF, VO output 0-5v, IO output 4-20MA .
About debugging: ? 1 zero adjustment First of all, make the system is in the idle state, adjust the marking ZERO potentiometer to adjust the zero offset. The multimeter is used to measure the output voltage or current, let show value as close as possible to the zero value display. Or change the magnification zero change will become big. 2 gain adjustment The system loading a certain weight value (the recommended range: 80% ~ 100% FS), the calculation of the output current value according to the load weight and the maximum weighting value relation, using the digital multimeter monitoring output, potentiometer to adjust amplifier gain spin-labeled SPAN. 3 the retest The system is in the idle state, measuring the zero output; loading a certain weight value, output voltage measurement whether fluoride expectation magnification If not, repeat steps 1, 2 adjust again.
Package includes:? ? 1 x Load Cell sensor Amplifier Transmitter?
