3pcs AD8302 Wideband Amplitude Phase Detection Impedance Analysis Module Amplifier Filter Mixer Loss
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 12 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615103895
Feature:
Single chip silicon bipolar device, amplitude / phase measurement The AD8302 is a fully integrated RF IC that measures the amplitude and phase between two independent input signals. The device operates from low frequencies to 2.7 GHz. The AD8302 contains two precision-matched wideband log amps, a wideband linear multiplier/phase detector, a 1.8V precision voltage reference, and an analog output proportional operation circuit. The input signal range is -60 dBm to 0dBm (reference impedance 50???) with a corresponding dynamic range of 60dB. The AD8302 output provides accurate amplitude measurements in the +/-30dB range with a slope of 30mV/dB; a phase measurement range of 0 to 180?ﾣ with a slope of 10mV/degree. Note: Please refer to application note AN-691 for module low frequency detection. The AD8302 is available in a 14-pin TSSOP package and operates over a temperature range of -40?ﾣC to 85?ﾣC. ? Module application: ? 1. Measurement of insertion loss and phase of an amplifier, filter or mixer 2. Measure the vector reflection coefficient of any load 3. Impedance analysis
Support cable:
BNC male to SMA male SMA male to SMA male
Single chip silicon bipolar device, amplitude / phase measurement The AD8302 is a fully integrated RF IC that measures the amplitude and phase between two independent input signals. The device operates from low frequencies to 2.7 GHz. The AD8302 contains two precision-matched wideband log amps, a wideband linear multiplier/phase detector, a 1.8V precision voltage reference, and an analog output proportional operation circuit. The input signal range is -60 dBm to 0dBm (reference impedance 50???) with a corresponding dynamic range of 60dB. The AD8302 output provides accurate amplitude measurements in the +/-30dB range with a slope of 30mV/dB; a phase measurement range of 0 to 180?ﾣ with a slope of 10mV/degree. Note: Please refer to application note AN-691 for module low frequency detection. The AD8302 is available in a 14-pin TSSOP package and operates over a temperature range of -40?ﾣC to 85?ﾣC. ? Module application: ? 1. Measurement of insertion loss and phase of an amplifier, filter or mixer 2. Measure the vector reflection coefficient of any load 3. Impedance analysis
Support cable:
BNC male to SMA male SMA male to SMA male
| Frequency Hz | Signal source RMS@50 ohm | Source phase (degrees) | Output voltage V | |||
| CH1 | CH2 | CH1 | CH2 | VM | VP | |
| 500K | 0.2V | 0.2V | 0 | 90 | 0.908V | 0.907V |
| 500K | 0.1V | 0.2V | 0 | 90 | 0.724V | 0.906V |
| 500K | 0.2V | 0.1V | 0 | 90 | 1.093V | 0.908V |
| 500K | 0.2V | 0.2V | 0 | 180 | 0.908V | 0.032V |
| 500K | 0.2V | 0.1V | 0 | 180 | 1.094V | 0.023V |
| 500K | 0.1V | 0.2V | 0 | 180 | 0.725V | 0.022V |
| 500K | 0.2V?/ | 0.2V | 0 | -90 | ||