OLED Version DevKit ESP32 Watch Development Board
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615106785
What is it?
? It is a ESP32 Watch development board.
Why did you make it?
? This product was planned at the same time of deauther wristband. I learned a lot of experience from deauther wristband and I knew ESP32 is a better choice for a Watch. ? The break ou pads are also designed to connect different sensors. ? TX/RX could be used to communicate with computer or other control board. ? 17/16 is IIC port could be connected with RTC module or other IIC sensors. ? SVP/SVN could input ADC signals. ? 25/26 could output DAC signals. ? What makes it special?
? Small size: 3.8x4.5cm Height:1.5cm Double 4 layer board 600mAh battery inside On/OFF Power Switch OLED version:1.3OLED SH1106(SDA-17,SCL-16) Buzzer-32
WS2812b RGB LED-33 Navigation Button(Up-19,Center-18,Down-5) OLED version external slide button(22,23) Highlight LED(27) Indicate charging LED(On means Charging,OFF means Full) Reset and Flash Button at Bottom board Break ou GPIOs(TX,RX,17,16,SVP,SVN,25,26,GND,3V)
SD Card support ? GPIO12--DAT2 GPIO13--DAT3 GPIO15--CMD GPIO14--CLK GPIO2--DAT0 GPIO4--DAT1 GPIO21--card
? Tutorial:
1. ? 2. ?? 3. ? 4.
?
Package Included:
1 x?DSTIKE ESP32 Watch DevKit
? It is a ESP32 Watch development board.
Why did you make it?
? This product was planned at the same time of deauther wristband. I learned a lot of experience from deauther wristband and I knew ESP32 is a better choice for a Watch. ? The break ou pads are also designed to connect different sensors. ? TX/RX could be used to communicate with computer or other control board. ? 17/16 is IIC port could be connected with RTC module or other IIC sensors. ? SVP/SVN could input ADC signals. ? 25/26 could output DAC signals. ? What makes it special?
? Small size: 3.8x4.5cm Height:1.5cm Double 4 layer board 600mAh battery inside On/OFF Power Switch OLED version:1.3OLED SH1106(SDA-17,SCL-16) Buzzer-32
WS2812b RGB LED-33 Navigation Button(Up-19,Center-18,Down-5) OLED version external slide button(22,23) Highlight LED(27) Indicate charging LED(On means Charging,OFF means Full) Reset and Flash Button at Bottom board Break ou GPIOs(TX,RX,17,16,SVP,SVN,25,26,GND,3V)
SD Card support ? GPIO12--DAT2 GPIO13--DAT3 GPIO15--CMD GPIO14--CLK GPIO2--DAT0 GPIO4--DAT1 GPIO21--card
? Tutorial:
1. ? 2. ?? 3. ? 4.
?
Package Included:
1 x?DSTIKE ESP32 Watch DevKit
