Machifit No Power Spindle Assembly Small Lathe Accessories B16 Drill Chuck Trimming Belt Set
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615185977
Description:
No power DIY woodworking cutting grinding spindle small lathe accessories fit for?table saw / bench drill / electric drill.
Specification:
Features:
-?The shipper and the synchronous wheel are equipped with the gasket isolation of 1mm to lock tightly.
- The rotation is smooth and without phase grinding, and the accuracy is good.
-?No power spindle, precision machining by grinding machine, precision of 0.005mm, that is, a high-precision spindle with less than one wire.
- DIY bench drill, bench mill, table saw and so on.
- Through the connecting rod, the shaft sleeve link is eliminated, and the drill clamp is installed directly, so the accuracy is higher.
- The non-powered spindle (Mohs drill chuck connecting rod) is precision machined with a grinding machine with an accuracy of 0.005MM. Can be used to make bench drills, bench mills, table saws, etc.?
1 X?XL10T 5mm hole synchronization wheel
1 X 120XL?Timing belt
1 X?Wrench
1 X?Drill chuck connecting rod
1 X?XL20T 10mm hole synchronization wheel
1 X?10mm hole slider (including 2 bearings)
1 X 1.5-13mm B16?Drill?Chuck
1 X?M10?Shaft sleeve
(including shaft socket wrench, synchronous wheel wrench, drill clamp key)
More Details:?
No power DIY woodworking cutting grinding spindle small lathe accessories fit for?table saw / bench drill / electric drill.
Specification:
| Cutting ability | Unpowered spindle |
| Cutting depth | 10 (mm) |
| For saw blade size/diameter | 90 * 10 (mm) |
| No load speed | 10000 (RPM) |
| Scope of application | Making small saw |
| Power type | No power |
Features:
-?The shipper and the synchronous wheel are equipped with the gasket isolation of 1mm to lock tightly.
- The rotation is smooth and without phase grinding, and the accuracy is good.
-?No power spindle, precision machining by grinding machine, precision of 0.005mm, that is, a high-precision spindle with less than one wire.
- DIY bench drill, bench mill, table saw and so on.
- Through the connecting rod, the shaft sleeve link is eliminated, and the drill clamp is installed directly, so the accuracy is higher.
- The non-powered spindle (Mohs drill chuck connecting rod) is precision machined with a grinding machine with an accuracy of 0.005MM. Can be used to make bench drills, bench mills, table saws, etc.?
Installation tips:
1. Pay attention to the mounting direction of the bearing, and carefully look at the description diagram or video.
2. Do not damage the bearing blindly. Patience and carefulness are the key points of mechanical work.
3. Various methods: to activate the brain and complete the assembly.
4. The sliding block and the contact surface of the synchronous wheel shall be separated by gasket to prevent phase grinding.The gasket is small. Don't lose it.
1 X?XL10T 5mm hole synchronization wheel
1 X 120XL?Timing belt
1 X?Wrench
1 X?Drill chuck connecting rod
1 X?XL20T 10mm hole synchronization wheel
1 X?10mm hole slider (including 2 bearings)
1 X 1.5-13mm B16?Drill?Chuck
1 X?M10?Shaft sleeve
(including shaft socket wrench, synchronous wheel wrench, drill clamp key)
More Details:?