3 in 1 2-6S RC Lipo Battery Voltage Meter Monitor Tester Signal Loss Alarm & Loss Aircraft Finder &
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 12 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615154339
.size_table_start table,.size_table_start table tr td { border:2px solid #ddd;}.size_table_start table { width: 100%; min-height: 25px; line-height: 25px; text-align: center; border-collapse: collapse;}.size_table_start,.size_table_end {clear:both;}
3 in 1 2-6S RC Lipo Battery Voltage Meter Monitor Tester
a?? Signal Loss Alarm & Loss Aircraft Finder & Low Voltage Buzzer
a?? DIY for RC Models
Description This is a 3in1 LiPo Battery monitor, Discovery buzzer & Signal loss alarm functions. Built-in ultrahigh brightness LED & twin loud buzzers. Item Name: Signal Loss Alarm Loss Aircraft Finder Working voltage: 5.2-26V DC, 2-6Cells LiPo Standby current less than 10mA Working current, Max 120mA (blinking & beeping) Voltage threshold setting: 3.4-3.7V/cell (Red LED) Twin loud buzzers, 85db each Ultrahigh Brightness LED, 20lm, 0.2w, Blue
Features Suit for fixed-wing copters, helicopters, multicopters, RC cars, etc
With Battery monitor function Long press 3 seconds to enter the voltage threshold setting; short press to select voltage threshold value between 3.4-3.7V (red led indicate); 10 seconds with no operation, will auto save the current setting. If the total voltage is below the holding value X cell, the alarm will continue to beep and flash blue until the voltage reaches or exceeds the set value.
With Discovery buzzer function Only plug the Y cable wire to Aux channel of receiver to enable the function;? Available signal of receiver is a must , the alarm is started by manual;
With Signal loss alarm function Firstly turn on the transmitter, and plug the alarm to reciever throttle channel with? Y cable wire, then turn on the receiver. This function is auto start. When the receiver is power on, the alarm will auto start in following situations : Turn off the transmitter,and do not turn on it in 1 minute, so that the reciever receive no signal. Transmitter is on, but no joystick action has been detected in 1 minute, or unchanged signal. It continue to beep in bibi...bibi...bibi, and flash blue
Package Included 1 x 3 in 1 Signal Loss Alarm Loss Aircraft Finder 1 x Y cable wire
a?? Signal Loss Alarm & Loss Aircraft Finder & Low Voltage Buzzer
a?? DIY for RC Models
Description This is a 3in1 LiPo Battery monitor, Discovery buzzer & Signal loss alarm functions. Built-in ultrahigh brightness LED & twin loud buzzers. Item Name: Signal Loss Alarm Loss Aircraft Finder Working voltage: 5.2-26V DC, 2-6Cells LiPo Standby current less than 10mA Working current, Max 120mA (blinking & beeping) Voltage threshold setting: 3.4-3.7V/cell (Red LED) Twin loud buzzers, 85db each Ultrahigh Brightness LED, 20lm, 0.2w, Blue
Features Suit for fixed-wing copters, helicopters, multicopters, RC cars, etc
With Battery monitor function Long press 3 seconds to enter the voltage threshold setting; short press to select voltage threshold value between 3.4-3.7V (red led indicate); 10 seconds with no operation, will auto save the current setting. If the total voltage is below the holding value X cell, the alarm will continue to beep and flash blue until the voltage reaches or exceeds the set value.
With Discovery buzzer function Only plug the Y cable wire to Aux channel of receiver to enable the function;? Available signal of receiver is a must , the alarm is started by manual;
With Signal loss alarm function Firstly turn on the transmitter, and plug the alarm to reciever throttle channel with? Y cable wire, then turn on the receiver. This function is auto start. When the receiver is power on, the alarm will auto start in following situations : Turn off the transmitter,and do not turn on it in 1 minute, so that the reciever receive no signal. Transmitter is on, but no joystick action has been detected in 1 minute, or unchanged signal. It continue to beep in bibi...bibi...bibi, and flash blue
Package Included 1 x 3 in 1 Signal Loss Alarm Loss Aircraft Finder 1 x Y cable wire
