1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod 1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod 1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod 1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod 1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod 1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod
1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod 1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod 1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod 1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod
1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod
+2

1 Channel 5V Low Level Trigger Relay Module Optocoupler Isolation Terminal BESTEP for Arduino - prod

New 20 available
R334.00
Shipping
R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate
The seller has indicated that they will usually have this item ready to ship within 12 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Seller
Buyer protection
Returns
Replacement Guarantee: 7 Days: We stand by this guarantee
Get it now, pay later

Product details

Condition
New
Location
International
Bob Shop ID
648341786
Description: Normally open interface maximum load: AC 250V/10A, DC 30V/10A. SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA. Fault-tolerant design, the relay will not move even if the control line is broken. Power indicator (green), relay status indicator (red). The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient.

Two module interface: 1. DC+: Connect the power supply positive pole (voltage 3.3V). 2. DC-: Connect the power negative pole. 3. IN: Low level (3.3V) control relay pull in. Relay output terminal: 1. NO:Relay normal open, the relay suspends before pulling in, and then short-connect with the COM. 2. COM: Relay common interface 3. NC:Relay normal close,short connected with COM beforepulling inand suspended afterpulling in. Package Included:

1 x1 Channel 5V Relay Module











Add to cart

Recently viewed

See more
Esp32/esp8266 Burner Usb-ttl Adapter Board Development Tool Esp-t01
New
R357.00
Three-section Hidden Buffer Slide Rail Damping Slide Rail Support
New
R736.00
Set Of 2 Trans Input/Output Sensor / Vehicle Speed Sensor Fit for Cube 31935-8E006 31935-8E007
New
R504.00
Programmable Full-color RGB LED Light Color Light Modulator PWM Speed Controller Panel
New
R421.00

Similar products

6 Channel 24V Relay Module Low Level Trigger With Optocoupler Isolation BESTEP for Arduino - product
New
R409.00
BESTEP 1 Channel 24V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger
New
R374.00
3pcs 1 Channel 3.3V Low Level Trigger Relay Module Optocoupler Isolation Terminal
New
R372.00
10pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High Low Level Trigger
New
R755.00