12 Volt Switched Mode Power Supply (PSU) for CCTV, HDD, Wifi AP | 60 Watt or 90 Watt or 120 Watt
You can use it on any 12 Volt Device e.g Router, Wifi Access Point and CCTV Cameras, 5 Amps is enough to provide constant 50watt to all devices and will power 3-4 cameras from one power supply.
12 Volt/60 Watt Max Usage Switched Mode Power Supply Specifications - No Power cord included
INPUT
- Input range : 85 ~ 264 VAC
- Input frequency : 47 ~ 63 Hz
- Inrush current : 15A at 115VAC; 30A at 230VAC; cold start at 25
- Input current : 1.5A Max
- Leakage current : 0.5 mA at 50/60 Hz 264VAC input
OUTPUT Rated output power : 60 Watts Max (50 Watts or less recommended to prevent device 80%+ power usage and overheating)
- DC Connector : 5.5mm OD & 2.1mm ID (Check DC Input size same on device but most 12 Volt devices uses this diameter on DC Power connector)
- Output voltage : 12V± 4%
- Output current : 5A
- OL protection 96% to 104% above peak rating
- Ripple & noise 200mV at rated load
- Operating temp : 0 to 50 ambient derate each output at 4.0% per degree from 50 to 60
- Storage temp. 40 to 85
- Operating humidity 5% to 95% (non-condensing)
- MTBF 100,000 hours at full load and 25 ambient conditions (demonstrated)
12 Volt/90 Watt Max Usage Switched Mode Power Supply Specifications - No Power cord included
INPUT
- Input range : 85 ~ 264 VAC
- Input frequency : 47 ~ 63 Hz
- Inrush current : 15A at 115VAC; 30A at 230VAC; cold start at 25
- Input current : 1.5A Max
- Leakage current : 0.5 mA at 50/60 Hz 264VAC input
OUTPUT
- Rated output power : 90 Watts Max (70 Watts or less recommended to prevent device 80%+ power usage and overheating)
- DC Connector : 5.5mm OD & 2.1mm ID (Check DC Input size same on device but most 12 Volt devices uses this diameter on DC Power connector)
- Output voltage : 12V± 4%
- Output current : 7.5A
- OL protection 96% to 104% above peak rating
- Ripple & noise 200mV at rated load
ENVIRONMENTAL
- Operating temp : 0 to 50 ambient derate each output at 4.0% per degree from 50 to 60
- Storage temp. 40 to 85
- Operating humidity 5% to 95% (non-condensing)
- MTBF 100,000 hours at full load and 25 ambient conditions (demonstrated)
12 Volt/120 Watt Max Usage Switched Mode Power Supply Specifications - No Power cord included
INPUT
- Input range : 100 ~ 264 VAC
- Input frequency : 50 ~ 60 Hz
- Inrush current : 100~240Vac 50/60Hz max: 90~264Vac 47/63Hz
OUTPUT Rated output power : 120 Watts Max
- DC Connector : 5.5mm x 2.5mm, compatible with 5.5mm x 2.1mm (Check DC Input size same on device but most 12 Volt devices uses this diameter on DC Power connector)
- Output voltage : 12V± 5%
- Output current : 10A
- OL protection 115% to 135% above peak rating
- Operating temp : 0 to 50ºC ambient derate each output at 4.0% per degree from 50 to 60
- Storage temp. 40 to 80ºC
- Operating humidity 20% to 90% (non-condensing)
Note!!! Please do not buy a power supply rated for less watts than being used. Adding multiple strings of LED lights to a power supply or more cameras / hard drives that uses more than 80% of the rated output of the power supply, will cause overheating to the power supply and damage / cut-off. Make sure you calculate max watts on connected devices to be less than 80% of power supply max amps/watts rating.
Power Cord that works with the power adapter
/1-5-meter-pc-hdtv-power-cable-3-pin-sa-electrical-plug-to-kettle-cord-iec-plug-c13-plug/
