16x16mm TeenyF4 Pro F4 Flight Controller w/ OSD Buck-Boost Converter for Micro FPV Racing Drone 1-2s
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615155339
16x16mm TeenyF4 Pro F4 Flight Controller w/ Betalflight OSD & Buck-Boost Converter for Micro FPV Racing Drone??
Specification:
Item Name: Omnibus F4 FC Integrated with Betaflight OSD
Model:?TeenyF4 Pro
Processor: STM32F405RGT6 Sensor: MPU-6000 (connected by SPI) Firmware version: betaflight_3.2.0_OMNIBUSF4SD
Input Voltage: 1-2S Lipo
Size: 20*20mm Mounting Hole: 16*16mm Mount Hole Diameter: 2mm Weight: 2.2g
-?Built-in Buck-Boost Converter
- Receiver: PPM, IBUS, SBUS, DSM2, DSMX etc. - Suitable for Micro FPV brushless frame
Features:
-Support?programmable?LED?Strip (turn?off?transponder?before?using)
-Support?BLheli/BLHELI_S?suite?Pass-through?ready
-Support?PPM,Oneshot125, Oneshot42,?Multishot, Dshot150, Dshot300,?Dshot600
-Support?the?newest?DSHOT?ESC
-Built-in?voltage?detection,?alarm
-Built-in?Betaflight-OSD , Configure?by?Betaflight?GUI
-Buzzer?Ready?(Solder?pin)
-LED_STRIP?Ready?(Solder?pin)
? Setting Notice:
- SBUS/IBUS/DSMX receiver please configure RX1 (UART1) as input, and enable Serial_RX? - PPM receiver dona??t need to enable Serial_RX? - DSM/DSM2/DSMX receiver power from 3.3V? - SBUS and PPM receiver power from 5V
Package Included:
1x TeenyF4 Pro flight controller board 4x M2*5+5 Nylon column 4x M2 Nuts 4x M2 Screw
Specification:
Item Name: Omnibus F4 FC Integrated with Betaflight OSD
Model:?TeenyF4 Pro
Processor: STM32F405RGT6 Sensor: MPU-6000 (connected by SPI) Firmware version: betaflight_3.2.0_OMNIBUSF4SD
Input Voltage: 1-2S Lipo
Size: 20*20mm Mounting Hole: 16*16mm Mount Hole Diameter: 2mm Weight: 2.2g
-?Built-in Buck-Boost Converter
- Receiver: PPM, IBUS, SBUS, DSM2, DSMX etc. - Suitable for Micro FPV brushless frame
Features:
-Support?programmable?LED?Strip (turn?off?transponder?before?using)
-Support?BLheli/BLHELI_S?suite?Pass-through?ready
-Support?PPM,Oneshot125, Oneshot42,?Multishot, Dshot150, Dshot300,?Dshot600
-Support?the?newest?DSHOT?ESC
-Built-in?voltage?detection,?alarm
-Built-in?Betaflight-OSD , Configure?by?Betaflight?GUI
-Buzzer?Ready?(Solder?pin)
-LED_STRIP?Ready?(Solder?pin)
? Setting Notice:
- SBUS/IBUS/DSMX receiver please configure RX1 (UART1) as input, and enable Serial_RX? - PPM receiver dona??t need to enable Serial_RX? - DSM/DSM2/DSMX receiver power from 3.3V? - SBUS and PPM receiver power from 5V
Package Included:
1x TeenyF4 Pro flight controller board 4x M2*5+5 Nylon column 4x M2 Nuts 4x M2 Screw