25.5x25.5mm Happymodel CrazyF411 AIO F4 2-4S Flight Controller Built-in 20A BL_S ESC & Frsky Receive
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615157330
Specification:
Brand Name: Happymodel Model: CrazyF411 AIO Item Name:??F4 Flight Controller Built-in 20A BL_S ESC & Frsky Receiver
Features: - 25.5x25.5mm FC AIO ESC board for toothpick . - Most powerful for whoop / toothpick style flight - Supports 2-4s battery input and provides 20A to the motors.? - Also Integrated SPI Frsky receiver working with D8/D16 protocols. This integrated receiver has PA/LNA power amplifier and the diversity antenna. This should give more control range for this flight controller.
Bind procedure: Make the on board receiver get into bind mode: For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type a??bind_rx_spia?? ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is a??bind_rxa??
Make your transmitter get into bind mode . If bind is successful the red led will starting to blink.? ?The red LED wouldna??t blinking when binding with some new ACCESS firmware frsky radio? , but the bind is actual successful , need to go to CLI command and type a??savea?? to finish the binding .
SPI Receiver option: Frsky_D compatible with Frsky D8 protocol Frsky_X compatible with Frsky non-eu D16 protocol Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support) SFHSS compatible with Futaba S-FHSS protocol
Package Included: 1x F4 AIO ESC RX Board 1x Cable with Conenctor 1x bag of Screws & Standoffs
Brand Name: Happymodel Model: CrazyF411 AIO Item Name:??F4 Flight Controller Built-in 20A BL_S ESC & Frsky Receiver
| F4 Flight Controller | MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 2-4S battery input (DC 8V-17V) Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Frsky D8/D16 SPI receiverBuilt-in 2.4G Power Amplification Built-in Betaflight OSD(SPI Control) Built-in Current meter Built-in 5V 1.5A BEC Built-in voltage detection Firmware target: MATEKF411RX Yaw Degrees should set to a??-90 degreea?? to match the flight direction |
| Onboard 20A ESC | MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Current: 20A continuous peak 25A (5 seconds) Support BLHeliSuite programmable Factory firmware: F_H_40_REV16_7.HEX Default protocol: DSHOT600 |
| Internal Frsky NON-EU receiver Version | SPI BUS receiver Frsky D8/D16 compatibleCompatible Non EU transmitter both D8 mode and D16 mode Channels: 8ch/16chDual antenna Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 400m |
Features: - 25.5x25.5mm FC AIO ESC board for toothpick . - Most powerful for whoop / toothpick style flight - Supports 2-4s battery input and provides 20A to the motors.? - Also Integrated SPI Frsky receiver working with D8/D16 protocols. This integrated receiver has PA/LNA power amplifier and the diversity antenna. This should give more control range for this flight controller.
Bind procedure: Make the on board receiver get into bind mode: For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type a??bind_rx_spia?? ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is a??bind_rxa??
Make your transmitter get into bind mode . If bind is successful the red led will starting to blink.? ?The red LED wouldna??t blinking when binding with some new ACCESS firmware frsky radio? , but the bind is actual successful , need to go to CLI command and type a??savea?? to finish the binding .
SPI Receiver option: Frsky_D compatible with Frsky D8 protocol Frsky_X compatible with Frsky non-eu D16 protocol Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support) SFHSS compatible with Futaba S-FHSS protocol
Package Included: 1x F4 AIO ESC RX Board 1x Cable with Conenctor 1x bag of Screws & Standoffs
