2CH Active H/L 3V OptoCoupler Relay Module

New
Indicative market price: R118.54
-+
54 available
R107.76
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item ready to ship within 2 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Get it now, pay later
Seller
Buyer Protection

Product details

Condition
New
Location
South Africa
Product code
2716
Bob Shop ID
613701063

Relays are always good to have especially for electronics projects. The relay itself offers two main benefits:

  • Isolation of low voltage system against high voltage system, example 5VDC and 240VAC
  • Allow electronics with low voltage to control high power load, for example from Arduino to AC light bulb.

This is not an ordinary Relay breakout. It comes with 2 channels 3.3V activation relays, ready to control 250VAC at 10A. Extra isolation with optocoupler at the front of control and the activation logic for the relay is configurable via a mini jumper. In simple words, the relay can be configured as 3.3V(High) activation or 0V(Low) activation. This is the universal Relay breakout board and we like it.

It comes with three (3) screw terminals for each relay output:

NO (Normally Opened),
NC (Normally Closed),
COM (Common),

and screw terminals for the control signal from a microcontroller such as Arduino or micro:bit. The control signal is optoisolated, protected. It even comes with power and activation indicator LEDs for the relay. Easy to use and suitable for beginners, and of course students too.

Input power and signal:

  • DC+ = +3.3VDC
  • DC- = GND (Ground or 0V)
  • In1 = Control signal, 3.3V as logic High; 0V as logic Low
  • In2 = Control signal, 3.3V as logic High; 0V as logic Low

If you need to control AC or high current, high voltage load, this will be the perfect board.



Note: We notice the DC+ and DC- need to be 3.3V and the In1 (control signal) needs to be 3.3V or Ground to make it works properly.

Features

  • 3.3V One (single) channel relay module
  • Configurable Activation Logic, High or Low, via mini jumper
  • Maximum Current Rating: 10A
  • Maximum Voltage Rating: AC 250V
  • Can control various appliances with large current and high voltage
  • Can be controlled directly by 3.3V microcontrollers such as Arduino, micro:bit.
  • Build-in an Opto-Isolator for extra isolation and protection to the controller.
  • A power indicator LED, and another relay activation indicator LED


What's in the box?

1 x Two Channel Active Hing/Low 3V Optocoupler Relay Module

Resources

Instructables: Arduino 2 channels relay, the similar concept applied

Warning
Exercise proper caution when connecting mains driven equipment or appliances to relay module as lethal current will be present.

Note: Stock is currently available in South Africa for national shipping!

More from this seller

View all
M2.5 x 20mm Male Female Hex Brass Standoff Spacer
R8
R30 shipping
9% OFF
XD-05 Arduino Data Logging Shield Module
R127.49 R140.24
R30 shipping
9% OFF
Raspberry Pi Official Pi4 8GB Desktop Kit
R3,015.88 R3,317.47
R30 shipping
9% OFF
Dual USB 5V 2.4A Type-C LED USB Mobile Power Bank 18650 Charging Module
R103.12 R113.43
Add to cart

Similar products

9% OFF
Four channel 5V DC Relay Module
R81.08 R89.19
R30 shipping
Rain sensor module with relay module 12V
R122.53
R30 shipping
3Set 433MHz DC 12V24V 2-Way Remote Control Switch 2 Channel Relay Module Motor Forward and Reverse C
R979
R30 shipping
9% OFF
Modbus RTU 16-Ch Relay Module, RS485 Interface, Isolation Protection
R1,194.69 R1,314.16