3Pcs 4S 14.8V 16.8V 18650 Lithium Battery Protection Board Startable Electric Drill 40A Current
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615103493
Specifications:
Scope of application: Lithium batteries with nominal voltages of 3.6V and 3.7V Product size: 46*60*3.4mm Product weight: 10.3g Charging voltage: 16.8V-18.1V Continuous discharge current (upper limit): 40A (If the heat dissipation environment is not good, please reduce the load current to use) Continuous charging current (upper limit): 20A Applicable electric drill: electric drill with starting current below 80A and power below 135W.
Note:
1. To start the electric drill successfully, you need 4 power batteries of 15C-20C, or 8 power batteries of 10C-15C (ordinary 18650 cannot start the electric drill!! !). 2. Wire 0V, 4.2V, 8.4V, 12.6V, 16.8V strictly according to the diagram, and do not intentionally short-circuit. 3. For loads with brushed motors, try to connect a non-polar capacitor in parallel with the positive and negative terminals of the motor (withstand voltage above 25V, capacity 10uF-100uF) to prevent the reverse peak voltage generated by the motor from interfering with the protection board or breakdown MOS tube. 4. When connecting 4 sets of batteries in series, please ensure that the voltage of each set of batteries is the same. If they are not the same, please charge each set of batteries separately and use them in series. . . During the discharge test, the battery with the faster voltage drop is a bad battery.
Package Included:
3 x 4S 14.8V 16.8V 18650 Lithium Battery Protection Board
Scope of application: Lithium batteries with nominal voltages of 3.6V and 3.7V Product size: 46*60*3.4mm Product weight: 10.3g Charging voltage: 16.8V-18.1V Continuous discharge current (upper limit): 40A (If the heat dissipation environment is not good, please reduce the load current to use) Continuous charging current (upper limit): 20A Applicable electric drill: electric drill with starting current below 80A and power below 135W.
Note:
1. To start the electric drill successfully, you need 4 power batteries of 15C-20C, or 8 power batteries of 10C-15C (ordinary 18650 cannot start the electric drill!! !). 2. Wire 0V, 4.2V, 8.4V, 12.6V, 16.8V strictly according to the diagram, and do not intentionally short-circuit. 3. For loads with brushed motors, try to connect a non-polar capacitor in parallel with the positive and negative terminals of the motor (withstand voltage above 25V, capacity 10uF-100uF) to prevent the reverse peak voltage generated by the motor from interfering with the protection board or breakdown MOS tube. 4. When connecting 4 sets of batteries in series, please ensure that the voltage of each set of batteries is the same. If they are not the same, please charge each set of batteries separately and use them in series. . . During the discharge test, the battery with the faster voltage drop is a bad battery.
Package Included:
3 x 4S 14.8V 16.8V 18650 Lithium Battery Protection Board
