This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1655
3pcs Q206 PCF8563 PCF8563T 8563 Module Clock Module RTC Module DIY Clock Kit
New
R292.00
Closed
11 May 24 00:04
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Buyer Protection
How you're covered
Get it now, pay later
Returns
Product information
Condition:
New
Location:
International
Bob Shop ID:
612368812
Features:
? 1.All that might be used is that in addition to the two required ports of SDA and SCL, the ints and COT that might be used are also cited. 2.Spare battery: when the system is out of power, the backup battery will power PCF8563 chip, PCF8563 low power consumption, and ensure that the battery can be used for normal power supply for ten years. 3.Crystal vibration: the new original original product crystal vibration, guaranteed the chip PCF8563 stable, accurate time. 4.The advantage of the chip itself: in the actual project of the shop owner, a variety of clock chips have been applied, and it is 5.found that this chip of philips is the most stable, the most accurate and the lowest power consumption. Clock chips such as DS1302 are too weak to recommend PCF8563 clock chips. ? Performance Indicators: ? It can be powered by a spare battery. Wide voltage range 1.0~ 5.5v. Ultra low power consumption: a typical value of 0.25uA. Through the I2C bus serial input/output. The output frequency of the programmable clock is 32.768khz, 1024Hz, 32Hz, 1Hz. There are four alarm functions and timer functions. It contains reset circuit, oscillator capacitance and power loss detection circuit. To open the leakage interrupt output. Read and write 400KHZ. Right INT interrupt output (generally not available) Cotangent clock output terminal (usually not available) The SCL IIC clock interface is connected to the single chip computer IO port. SDA IIC digital interface connected with single chip microcomputer IO port. The GND module is externally connected. VCC power interface external to 3.3v-5v. ? Package Included: ? 3 x Clock Module
? 1.All that might be used is that in addition to the two required ports of SDA and SCL, the ints and COT that might be used are also cited. 2.Spare battery: when the system is out of power, the backup battery will power PCF8563 chip, PCF8563 low power consumption, and ensure that the battery can be used for normal power supply for ten years. 3.Crystal vibration: the new original original product crystal vibration, guaranteed the chip PCF8563 stable, accurate time. 4.The advantage of the chip itself: in the actual project of the shop owner, a variety of clock chips have been applied, and it is 5.found that this chip of philips is the most stable, the most accurate and the lowest power consumption. Clock chips such as DS1302 are too weak to recommend PCF8563 clock chips. ? Performance Indicators: ? It can be powered by a spare battery. Wide voltage range 1.0~ 5.5v. Ultra low power consumption: a typical value of 0.25uA. Through the I2C bus serial input/output. The output frequency of the programmable clock is 32.768khz, 1024Hz, 32Hz, 1Hz. There are four alarm functions and timer functions. It contains reset circuit, oscillator capacitance and power loss detection circuit. To open the leakage interrupt output. Read and write 400KHZ. Right INT interrupt output (generally not available) Cotangent clock output terminal (usually not available) The SCL IIC clock interface is connected to the single chip computer IO port. SDA IIC digital interface connected with single chip microcomputer IO port. The GND module is externally connected. VCC power interface external to 3.3v-5v. ? Package Included: ? 3 x Clock Module