4-Channel Logic Level Shifter - Pre-soldered Headers

4-Channel Logic Level Shifter - Pre-soldered Headers

4 available / new
Indicative market price: R20.55
Only 4 left – grab it before it’s gone!
R18.68
Shipping
R65.00 Standard shipping applies to orders under R100.00, in most areas in South Africa. R35.00 Standard shipping applies to orders over R100.00. Some areas may attract a surcharge surcharge. This will be calculated at checkout if applicable.
Check my rate
The seller has indicated that they will usually have this item ready to ship within 2 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Seller
Buyer protection
Get it now, pay later

Product details

Condition
New
Location
South Africa
Product code
2666
Bob Shop ID
613701042

Note: This logic level shifter breakout comes pre-soldered with headers.

If you have ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be! The logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. Each level converter can convert 4 pins on the high side to 4 pins on the low side, with power supply pins on each side.

The usage of the level converter is very straightforward. The board needs to be powered from the two voltage sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the "HV" pin, low voltage (3.3V for example) to "LV", and ground from the system to the "GND" pin.

This module requires you to supply it with power from both the higher voltage level and the lower voltage level. Connect the higher voltage source to pin "HV" and its ground to pin "GND" near the "HV" pin. Also, connect the lower voltage source to pin "LV" and its ground to pin "GND" near the "LV" pin.

For example, if you were connecting your Arduino (5V signals) to an ESP8266 (3.3V signals), you would connect the "HV" pin on the module to the 5V supply pin on your Arduino and the "GND" pin near the "HV" pin to the "GND" pin on your Arduino. Then, you would connect the "LV" pin on the module to the 3.3V power source that is supplying power to the ESP8266 and connect the "GND" pin near the "LV" pin to the 3.3V power supply's ground. You would then connect the signal pin from your Arduino to one of the signal pins on this module (for example, pin "HV1"), and then you would connect the desired signal pin on the ESP8266 to the corresponding pin on this module ("LV1" if the higher voltage signal is connected to "HV1").

These are 4 Channel devices (works great for I2C or SPI) and will work with all microcontrollers, Arduino, Raspberry Pi, Intel Edison, etc. Use this module to connect two devices of different digital voltage levels. For example: connecting an Arduino (5V device) to an ESP8266 (3.3V device).

The logic level converter comes complete with header pins and can be used directly on a breadboard.

Features

  • Convert 4 pins on the high side to 4 pins on the low side or vice versa
  • With 2 rows, 6 pins per row
  • No. of channels: 4
  • Power from two voltage sources (high and low); high voltage goes to the HV pin and low voltage to the LV pin
  • Mutual transform between 3.3V and 5V
  • Digital Logic only, NOT Analog voltage.
  • Useful for IIC Protocol communication
  • Compatible with Arduino, PIC, Raspberry Pi, etc
  • Breadboard Compatible
  • Pinout labeled on modules
  • Dimensions (excluding pins): 15.2mm (0.6") length x 12.7mm (0.5") width x 2.5mm (0.1") height
  • Weight: 1.2g (0.04oz)

What's in the box?

1 x 4-Channel Logic Level Shifter - Pre-soldered Headers
Note: Stock is currently available in South Africa for national shipping!
Add to cart

Recently viewed

See more
Understanding and Dealing With Stroke Dr Keith Souter
R250.00
Poslab RFID Reader for WP68i PL-WP68i-RFID
R1,463.06
Barrier Terminal Block 1 Pole Dgr10 01 P 13 10 A(h)
R11.49
39% OFF
25V Multi-Function Power Tool Set - Chargeable Cordless Drill -JG20375126
R4,300.00 R7,000.00

Similar products

Arduino Pro Mini Atmega328 - Not Soldered
R110.00
2 PCS Mini RS232 Max3232 to TTL Level Conversion Board
R131.00
Pulse Zero Smart Environmental Monitor - 2.4 GHz
R4,278.96
RPI GPIO Shield (Arduino Layout, 5V Logic)
R227.76