4 In 1 Charger Discharger Boost 5V 2.1A Module for 3.7V 4.2V Battery DIY Mobile Power with Button
New
Indicative market price: R95.57
Shipping
Standard courier shipping from R60
R60 Standard shipping applies to orders under R100, in most areas in South Africa. R30 Standard shipping applies to orders over R100. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Free collection from
Henley on Klip, Meyerton
The seller allows collection for this item and will be in contact with the full collection address once the order is ready.
Ready for collection by Thursday, 23 May.
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 2 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
South Africa
Product code
1550
Bob Shop ID
613700976
trigger: input LOW(grounding)
Single Chip Using: If Small load KEY connect 20S single chip and supply with input LOW, the module will work well.
Specifications
About module pins
1 VIN: charge port
2 GND: charge port -
3 BAT: Battery
4 GND: Battery -
5 GND: output -
6 VOUT: output
7 KEY: trigger
Note:
1. In discharging mode(charging mode KEY function invalid), trigger KEY one time,output open; trigger two times, output close.
2. Output will open automatically if you connect load. If load below 50MA, the module will turn off output port; if load over 50MA, output port will always open.
3. Allow charging and discharging at the same time(output voltage should below 5V. Stop charging and stop discharging,you should reactivation the module.)
What's in the box?
1 x power module
1 x button
Resources
1. Charge/Discharge: All cables
2. Charge: Connect power supply and battery
3. Discharge: Connect battery and output
Note: Stock is currently available in South Africa for national shipping!
Single Chip Using: If Small load KEY connect 20S single chip and supply with input LOW, the module will work well.
Specifications
- Charge voltage: DC 4.5V-5.5V(Recommend DC 5V)
- Charging current: 0-2.1A
- Charge quiescent current: 100uA
- Full charge voltage: 4.2V -1%
- Discharge current: 0-2.4A
- Discharge quiescent current:50uA
- Discharge conversion efficiency: MAX 96%
- Output voltage: 5V
- Output current: 0-2.4A
- Operating ambient temperature: -20to 85
- Size: 25x16x4mm
- Weight: 2.3g
- PCB board design: Immersion Gold
- Battery protection: OCP/OVP/SCP/OTP
About module pins
1 VIN: charge port
2 GND: charge port -
3 BAT: Battery
4 GND: Battery -
5 GND: output -
6 VOUT: output
7 KEY: trigger
Note:
1. In discharging mode(charging mode KEY function invalid), trigger KEY one time,output open; trigger two times, output close.
2. Output will open automatically if you connect load. If load below 50MA, the module will turn off output port; if load over 50MA, output port will always open.
3. Allow charging and discharging at the same time(output voltage should below 5V. Stop charging and stop discharging,you should reactivation the module.)
What's in the box?
1 x power module
1 x button
Resources
1. Charge/Discharge: All cables
2. Charge: Connect power supply and battery
3. Discharge: Connect battery and output
Note: Stock is currently available in South Africa for national shipping!