This item has closed 2 buyers bought 2 items
View other items offered by SGN International380
.jpg){kind=link}
42cm DIY Plastic Path Maker Mold Manually Paving Cement Brick Stone Road Auxiliary Tools
New
Indicative market price: R1,169.60
R609.80
48% OFF
Closed
9 Apr 17 23:39
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 3 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Money-Back 7 Days
guarantee
Money-Back Guarantee:
7 Days: Full or Partial Refund , if the item is not as described If your item is significantly different from the sellers product description, you can A: Return it and get a full refund (EXCLUDING SHIPPING FEES), or B: Get a partial refund and keep the item.
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
South Africa
Product code
981499
Bob Shop ID
276558394
DIY Plastic Path Maker Mold Manually Paving Cement Mould
Use heavy-duty plastic mold that turns a little pre-mixed concrete into a concrete garden stepping stones for easiest access way to your garden.
A personalized brick mold, laying out the effect posted up like blocks of stones, so that makes the path more exotic, to create a style of your own garden path as you like and decorate your backyard landscape.
Keep the beauty and health of your plant by using garden steppingstones as your path way.
Specification:
Material: PP resin
Size: 42x43x4cm / 16.54x16.93x1.57in
Color: black
Warm Note:
1. Clean the concrete garden molds for reusing, spray them with garden hose.
2. Garden stone mold can be used again right after you pour the first garden stepping stone so you do not have to wait.
Package Included:
1 X Path Maker Mould
.jpg)
.jpg)
.jpg)
.jpg)
.jpg)
.jpg)
.jpg)
.jpg)
.jpg)
Use heavy-duty plastic mold that turns a little pre-mixed concrete into a concrete garden stepping stones for easiest access way to your garden.
A personalized brick mold, laying out the effect posted up like blocks of stones, so that makes the path more exotic, to create a style of your own garden path as you like and decorate your backyard landscape.
Keep the beauty and health of your plant by using garden steppingstones as your path way.
Specification:
Material: PP resin
Size: 42x43x4cm / 16.54x16.93x1.57in
Color: black
Warm Note:
1. Clean the concrete garden molds for reusing, spray them with garden hose.
2. Garden stone mold can be used again right after you pour the first garden stepping stone so you do not have to wait.
Package Included:
1 X Path Maker Mould
How to Make Pavement:
Step 1: Lay out the perimeter of the walkway and drive wooden stakes into the ground at each corner.
Step 2: For professional results, remove one inch of sod. Save the sod you remove and use it to fill in gaps once the walkway has set. If you plan to use the sod later, set it aside in a cool place and water.
Step 3: The mold comes with directions on how much concrete you need based on the length of walkway you're creating. Mix the concrete, adding color to make the walkway resemble cobblestone or brick.
Step 4: Wet the mold with water before you begin adding concrete.
Step 5: Beginning in one corner of the walkway, lay the mold in place.
Step 6: With a bucket or trowel, fill each cavity of the mold with concrete. The concrete should be level with the top of the mold.
Step 7: Smooth the surface with a trowel.
Step 8: In about five to ten minutes, lift the mold. You're ready to do the next section.
Step 9: Butt the mold against the first section and continue building your walkway. By rotating the mold one-quarter turn each time, you create a variation in the pattern.
Step 10: For curves, butt the outside corner of the mold to the existing walkway. Turn the mold to align with the curve. The mold will overlap the existing concrete on the inside of the curve.
Step 11: Press the mold down, cutting into the existing concrete. Fill the mold with concrete.
Step 12: Remove the mold and blend the combined castings, eliminating cut lines.
Step 13: Position the mold and pour the remaining sections.
Step 14: Sprinkle sand or dry mortar mix on top of your walkway after it is set. Brush it into the joints with a broom.
Step 15: Mist lightly with a garden hose.
Step 16: Place six-mil plastic sheeting over the concrete for two to three days to prevent the surface from drying too quickly and cracking.
Step 17: After your walkway has cured, protect its finish with a concrete sealer. Follow the manufacturer's instructions for application. The sealer forms a tough, water-resistant finish that is virtually unaffected by the elements.
Step 1: Lay out the perimeter of the walkway and drive wooden stakes into the ground at each corner.
Step 2: For professional results, remove one inch of sod. Save the sod you remove and use it to fill in gaps once the walkway has set. If you plan to use the sod later, set it aside in a cool place and water.
Step 3: The mold comes with directions on how much concrete you need based on the length of walkway you're creating. Mix the concrete, adding color to make the walkway resemble cobblestone or brick.
Step 4: Wet the mold with water before you begin adding concrete.
Step 5: Beginning in one corner of the walkway, lay the mold in place.
Step 6: With a bucket or trowel, fill each cavity of the mold with concrete. The concrete should be level with the top of the mold.
Step 7: Smooth the surface with a trowel.
Step 8: In about five to ten minutes, lift the mold. You're ready to do the next section.
Step 9: Butt the mold against the first section and continue building your walkway. By rotating the mold one-quarter turn each time, you create a variation in the pattern.
Step 10: For curves, butt the outside corner of the mold to the existing walkway. Turn the mold to align with the curve. The mold will overlap the existing concrete on the inside of the curve.
Step 11: Press the mold down, cutting into the existing concrete. Fill the mold with concrete.
Step 12: Remove the mold and blend the combined castings, eliminating cut lines.
Step 13: Position the mold and pour the remaining sections.
Step 14: Sprinkle sand or dry mortar mix on top of your walkway after it is set. Brush it into the joints with a broom.
Step 15: Mist lightly with a garden hose.
Step 16: Place six-mil plastic sheeting over the concrete for two to three days to prevent the surface from drying too quickly and cracking.
Step 17: After your walkway has cured, protect its finish with a concrete sealer. Follow the manufacturer's instructions for application. The sealer forms a tough, water-resistant finish that is virtually unaffected by the elements.