Similar products

12V 30A 1 Channels Relay With Optocoupler Isolation

Netram Technologies

R87.40

Add

R30 shipping

8 Channel Relay Module 24V with Optocoupler Isolation Relay Module Geekcreit for Arduino - products

szulou

R426

Add

R30 shipping

12V 6 Channels Optocoupler Isolation Relay: Low Level

Netram Technologies

R126.50

Add

R30 shipping

YYS-1 Programmable 4 Channel LED Relay Module Signal Trigger Delay Timer Relay PLC... (VOLTAGE: 12V)

szulou

R629

Add

4CH Channel Optocoupler Isolation Relay Module 5V/12V/24V SCM PLC Signal Amplifier... (VOLTAGE: 12V)

New

R492.00

Closed 9 Jun 24 23:05

Add to cart

Shipping

Standard courier shipping from R30

R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate

Ready to ship in

The seller has indicated that they will usually have this item ready to ship within 12 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:

Standard Delivery

Main centres:	1-3 business days
Regional areas:	3-4 business days
Remote areas:	3-5 business days

Returns

Replacement 7 Days guarantee

Replacement Guarantee: 7 Days: We stand by this guarantee

Get it now, pay later

Seller

szulou1905

93.56% Positive ratings

Buyer Protection

How you're covered

Product details

Condition

New

Location

International

Bob Shop ID

615104201

SELECTED OPTION:
VOLTAGE: 12V

Structural Features: ? 1. Use Hongfa relay, stable and reliable performance; 2. Compatible with two input modes of positive control and negative control; 3. Each channel has an LED action indicator for a more intuitive understanding of product performance; 4. Each channel adopts optocoupler isolation to enhance anti-interference performance and isolation performance; 5. At the same time, the power supply and the IN control terminal are independently controlled; 6. The module adopts the standard DIN rail-type installation design, which is convenient and quick to install, firm and stable. ? Technical Parameters: ? 1. Trigger signal: DC5V / 12 / 24V (Optional) 2. Each trigger signal current: 5mA 3. Power supply voltage: DC5V / 12 / 24V 4. Each coil current: 18.8mA 5. Contact type: one normally open and one normally closed (single pole) 6. Maximum load current of each contact: 10A 7. Action time: below 12ms 8. Reset time: less than 4ms 9. Maximum switching frequency: 18000 times / hour 10. Mechanical life: more than 20 million times 11. Relay installation: plug-in type (No) 12: Module installation method: DIN standard rail installation

Positive control wiring introduction: ? 1. Power input terminal: VCC is connected to the positive voltage, GND is connected to the negative voltage, and S / S is connected to the negative voltage IN1, IN2 are connected to positive voltage control, IN1 controls KI terminal, IN2 controls K2 terminal 2. Control device output: The output terminal is clearly marked with 234, 3 is a common point, 2 is normally open, and 4 is normally closed. K1, K2 means two relays work. ? Negative control wiring? introduction : ? 1. Power input terminal: VCC is connected to the positive voltage, GND is connected to the negative voltage, and S / S is connected to the positive voltage IN1, IN2 are connected to negative voltage control, IN1 controls KI terminal, IN2 controls K2 terminal 2. Control device output: The output terminal is clearly marked with 234, 3 is a common point, 2 is normally open, and 4 is normally closed. KI, K2 means two relays work.

Package includes:

1 x Relay board