5pcs DC-DC 9V/12V/24V to 5V Step Down Regulator USB Charging Car Power Supply Step-down Buck Chargin
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615102491
Feature:
Product size: 35.5 x 17 x 8.3mm Input voltage range: 6-26V Output voltage: 5.2V (considering the charging line loss, the output is about 5.2V, the load is about 5V) Upper limit output current: 3A (in the case of no heat sink, the stable output upper limit current is 2A) ? Precautions: ? 1. The positive and negative poles cannot be reversed, and the input voltage should not exceed 26V, otherwise the chip will be damaged! 2. When powering on, you can't touch the sampling resistor and IC pin on the circuit board by hand. Otherwise, the output voltage may be suddenly damaged and damage the device! 3. Explain to some customers with electronic basics: Do not think that the nominal 3A current will burn out the equipment. The charging current is determined by the device. The charging current for most devices is 0.8-1.5A. ? Tip: This is a step-down charging module. The current indicated by 2A refers to the upper limit current of the load. It cannot be compared with the 2A current indicated by the charger.
Package includes:
5 x Power supply module
Product size: 35.5 x 17 x 8.3mm Input voltage range: 6-26V Output voltage: 5.2V (considering the charging line loss, the output is about 5.2V, the load is about 5V) Upper limit output current: 3A (in the case of no heat sink, the stable output upper limit current is 2A) ? Precautions: ? 1. The positive and negative poles cannot be reversed, and the input voltage should not exceed 26V, otherwise the chip will be damaged! 2. When powering on, you can't touch the sampling resistor and IC pin on the circuit board by hand. Otherwise, the output voltage may be suddenly damaged and damage the device! 3. Explain to some customers with electronic basics: Do not think that the nominal 3A current will burn out the equipment. The charging current is determined by the device. The charging current for most devices is 0.8-1.5A. ? Tip: This is a step-down charging module. The current indicated by 2A refers to the upper limit current of the load. It cannot be compared with the 2A current indicated by the charger.
| Project | Min.Value | Typical Value | Max.Value | Unit |
| Standby current (Ven=0V) | 15 | 20 | 25 | uA |
| No-load current | 8 | 12 | 18 | mA |
| Input voltage | 6 | 12 | 26 | V |
| The output voltage | 5.1 | 5.25 | 5.4 | V |
| Output current | 0 | 2 | 3 | A |
| Overcurrent protection current | 5 | 5.5 | 6 | A |
| Conduction internal resistance | 80 | 100 | 120 | m?? |
| On-off level | 335 | 385 | 435 | KHz |
| High temperature protection | 85 | 90 | 130 | ?ﾣC |
| Conversion efficiency (I=7V, 0=5V) | 93 | 95 | 97 | % |
| Ambient temperature | -40 | 25 | 85 | ?ﾣC |
Package includes:
5 x Power supply module