Name: 7.3inch ACeP 7-Color E-Paper E-Ink Display Module, 800×480 Pixels, SPI Communication
SKU: 2658
Price: 1738.84 ZAR
Availability: InStock

7.3inch ACeP 7-Color E-Paper E-Ink Display Module, 800×480 Pixels, SPI Communication

New

2 available

Indicative market price: R1,912.72

Only 2 left – grab it before it’s gone!

R1,738.84

Shipping

R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate

The seller has indicated that they will usually have this item ready to ship within 2 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:

Standard Delivery

Main centres:	1-3 business days
Regional areas:	3-4 business days
Remote areas:	3-5 business days

Seller

PiShop SA2595

99.09 % Positive ratings

Buyer protection

How you're covered

Get it now, pay later

Condition

New

Location

South Africa

Product code

2658

Bob Shop ID

650021512

7.3 7-Colour E-Paper Module

Low power, wide viewing angle, paper-like effect without electricity

Ideal for price tags, shelf labels, industrial instruments...

Features at a glance

Advanced Color ePaper (ACeP) technology, supports 7-Color display
No backlight, keeps displaying last content for a long time even when power down
Ultra low power consumption, basically power is only required for refreshing
Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
SPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/STM32, etc.
Onboard voltage translator, compatible with 3.3V/5V MCUs
Comes with development resources and manual(driver board schematic, examples for Raspberry Pi/Arduino/STM32)

Specifications

operating voltage	3.3V/5V	display color	7-Color
interface	3-wire SPI, 4-wire SPI	grey scale	2
outline dimensions	170.2 × 111.2mm	full refresh time	35s
display size	160 × 96mm	refresh power	<49.4mW (typ.)
DOT PITCH	0.2 × 0.2 mm	standby current	<0.01uA (almost none)
RESOLUTION	800×480 pixels	viewing angle	>170°

Advantages of EINK

E-paper display utilizes microcapsule electrophoretic technology for displaying, the principle is: charged particles suspended in clear fluid will move to sides of microcapsule when electric field is applied, making the microcapsule become visible by reflecting ambient light, just as traditional printed paper.
E-paper display will clearly display images/texts under lamplight or natural light, requires no backlight, and features nearly up to 180° viewing angle. It is usually used as e-reader due to its paper-like effect.

Standard Raspberry Pi 40PIN GPIO Header

Compatible With Raspberry Pi Series Boards, Jetson Nano

Onboard SPI Control Interface

For Use With Controller Boards Like Raspberry Pi/Jetson Nano/Arduino/STM32

VCC	Power (3.3V / 5V input)
GND	Ground
DIN	SPI MOSI pin
SCLK	SPI SCK pin
CS	SPI chip selection, low active
DC	Data/Command selection (high for data, low for command)
RST	External reset, low active
BUSY	Busy status output pin

Application examples

Suitable for price Tags, asset/equipment Tags, shelf labels, conference name tags...

Outline dimensions

What's in the box?

1 x 7.3inch e-Paper (F)
1 x Driver Board and FFC cable
1 x PH2.0 20cm 8Pin
1 x RPi screws pack (2pcs)

Resources

WIKI: www.waveshare.com/wiki/7.3inch_e-Paper_HAT_(F)

Note: Stock is currently available in South Africa for national shipping!

Report a problem

7.3inch ACeP 7-Color E-Paper E-Ink Display Module, 800×480 Pixels, SPI Communication

Product details

Recently viewed

Similar products

7.3inch ACeP 7-Color E-Paper E-Ink Display Module, 800×480 Pixels, SPI Communication

Product details

0.0 out of 5

Recently viewed

Similar products