Adblue OBD2 Emulator for Man Truck Euro6 Adblue OBD2 Emulator for Man Truck Euro6 Adblue OBD2 Emulator for Man Truck Euro6 Adblue OBD2 Emulator for Man Truck Euro6 Adblue OBD2 Emulator for Man Truck Euro6
Adblue OBD2 Emulator for Man Truck Euro6 Adblue OBD2 Emulator for Man Truck Euro6 Adblue OBD2 Emulator for Man Truck Euro6 Adblue OBD2 Emulator for Man Truck Euro6 Adblue OBD2 Emulator for Man Truck Euro6

Adblue OBD2 Emulator for Man Truck Euro6

New 100 available
R614.00
Shipping
R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate
The seller has indicated that they will usually have this item ready to ship within 15 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Seller
Buyer protection
Get it now, pay later

Product details

Condition
New
Location
International
Product code
CRP4811
Bob Shop ID
621602946
1. It is possible to disable AdxBlue system by installing an AdxBlue emulator (programmable device) into the vehicle. You can switch it on/off anytime.
2. EURO6 AdBlue Emulators Disable system: AdxBlue system (Fully) / AdxBlue NOX sensor / DPF system / DPF temperature sensors / DPF regeneration.
3. After installing Euro6 Emulator, you can remove: DPF sensors / NOx sensor (only in DAF dona??t remove first NOx sensor) / Adblue temp. sensor / Adblue pump / Adblue level sensor / Adblue ECU.
4. Emulator Man Euro 6 does not need to be learned. You install emulator under the metal cover of AdBlue Pump on the right side behind the cab, and disconnect plug from AdBlue Pump and connect emulator.
5. Next, you need to remove the fuses:
F894(Multisensor In AdBlue tank)
F738 (+30 Signal of AdBlue pump)
F1084 (NOx sensor Upstream)
Fuse F737 is now fuse of emulator.
Fuse F1109 is the fuse of NOx sensor Downstream and A1191 mufler temperature sensor. This sensor needs to work correctly for DPF regeneration.
6. Finally, you need to remove Power from NOx downstream sensor. There are two ways options, one is to cut pin 1 in NOx sensor plug, the other way (better) is to remove pin 10 in X3212 plug. This plug is visible on rear of engine on the right side. This is TE plug (16 pin) with yellow key.

Add to cart

Recently viewed

See more
MARIO BALOTELLI - PANINI `FIFA WORLD CUP 2014` COLLECTION - `GAME CHANGER` FOIL TRADING CARD
New
R68.00
25.5cm Led Colors Changing Eiffel Tower Night Light Romantic Decorative Lights Decor Gift
New
R410.00
45% OFF
1Pc Dark Reda 25.4cm Fashion Design Wig
New
R552.00 R1,004.00
TENG - 5inch Inner/Bent Circlip Pliers - MB471-5
New
R549.00

Similar products

33% OFF
AdBlue Emulator EURO 4/5 OBD2 Emulator for MAN Trucks
New
R429.00 R644.00
MAN (M.A.N) Truck 37 Pin Cable Adapter OBD1 to OBD2
New
R200.00
38 Pin to OBD2 Truck Cable for IVECO
New
R328.00
33% OFF
Adblue OBD2 Emulator for DAF Trucks
New
R442.00 R663.00