B250K Linear 15mm Shaft (split) Mini Size Potentiometer
New
Shipping
Standard courier shipping from R60
R60 Standard shipping applies to orders under R100, in most areas in South Africa. R30 Standard shipping applies to orders over R100. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Free collection from
Capri, Cape Town
The seller allows collection for this item and will be in contact with the full collection address once the order is ready.
Ready for collection by Tuesday, 21 May.
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 2 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
South Africa
Product code
Id-13170
Bob Shop ID
597051496
B250K 15mm Split Brass Shaft Mini Potentiometer for volume and tone control on guitar. 
D3 = Pot diameter: 16mm (mini size) L = Shaft length: 15mm D1 = Shaft diameter: 6mm D2 = Shaft diameter for knob: 6mm (split)
250k pots are usually used for volume and tone control on single coil pickups
500k pots are usually used for volume and tone control on humbucker type pickups
Split shafts are suitable for push-on control knobs, solid shafts are suitable for knobs that have a tightening screw.
15mm Shaft pots are normally used for Fender style guitars or guitars with plastic pickguards / metal control plates that the pot goes through
18mm Shaft pots are normally used for Gibson style guitars as they often have wood that the pots must go through (or plastic pickguards if you purchase extra nut and washer to create a spacer at the back)
What is the difference between A pots and B pots?
"A" would denote an audio taper pot (most of the control happens between 7 - 10) and the "B" suffix would denote a linear taper pot (more even roll-off between 0 - 10)
A and B pots however are interchangeable and the only difference is the taper of the pot, or "how gradually it rolls off". Most manufacturers use either audio taper (A) pots for volume + tone or would use audio taper (A) for tone, and linear taper (B) for volume. This is also determined by player preference
D3 = Pot diameter: 16mm (mini size) L = Shaft length: 15mm D1 = Shaft diameter: 6mm D2 = Shaft diameter for knob: 6mm (split)250k pots are usually used for volume and tone control on single coil pickups
500k pots are usually used for volume and tone control on humbucker type pickups
Split shafts are suitable for push-on control knobs, solid shafts are suitable for knobs that have a tightening screw.
15mm Shaft pots are normally used for Fender style guitars or guitars with plastic pickguards / metal control plates that the pot goes through
18mm Shaft pots are normally used for Gibson style guitars as they often have wood that the pots must go through (or plastic pickguards if you purchase extra nut and washer to create a spacer at the back)
What is the difference between A pots and B pots?
"A" would denote an audio taper pot (most of the control happens between 7 - 10) and the "B" suffix would denote a linear taper pot (more even roll-off between 0 - 10)
A and B pots however are interchangeable and the only difference is the taper of the pot, or "how gradually it rolls off". Most manufacturers use either audio taper (A) pots for volume + tone or would use audio taper (A) for tone, and linear taper (B) for volume. This is also determined by player preference