View the relisted Item
Similar products
bluetooth 5.0 BT5.0 Audio Pro Audio Receiving Module Car Speaker Audio Power Amplifier Board Receive
Check my rate
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Product information
Feature:
BT5.0 Audio PRO continues the excellent basic functions of M28 (long-distance transmission, Bluetooth 5.0 backward compatible, lossless sound quality, etc.), and adds more user-friendly performance, as follows:
Charge while putting:
This product has a circuit of charging and discharging, which can directly charge the battery through the USB power supply, and Bluetooth can continue to work normally during the charging process, and truly realize the function of charging and discharging. Solve the pain point that some products can not be used during the charging process.
When powered by USB alone: The red light flashes, indicating that the power supply is normal.
When powered by a separate battery: The yellow light is always on, indicating that the battery power supply is normal; the yellow light flashes, indicating that the battery is low.
When the USB and battery are connected at the same time: The red light flashes to indicate that the battery is charging; the red light always indicates that the battery is fully charged.
(Note that if the USB input is suddenly disconnected during the charging and discharging process, there will be a few seconds of interruption due to the charge and discharge mode switching at this time, after which Bluetooth will automatically restart, automatically connect and maintain the previous playback state)
Incoming voice call function:
After the Bluetooth is connected, turn on the call audio mode in the Bluetooth settings. If the phone calls, you can answer or hang up the phone through the PLAY/STOP button. You can choose to send from the microphone of the original headset (provided that the headset has a call function, which is a 4-segment type) or from the onboard microphone (default), see the function description for details.
When the computer sound card is used:
Tin the pads in the two boxes corresponding to the Sound Card on the back of the module, and then connect it to the USB interface of the computer through the USB cable, which can be used as a sound card. That is, the sound played by the computer is output through the audio interface of the module. See function description for details. (Not enabled by default)
| Types | NO* | Button/interface | Features | Detailed operation |
| Button | 1 | ON/OFF | Bluetooth power on/off | Note that battery charging is not controlled by this switch. ON: Bluetooth starts to work and the blue light is on. OFF: Bluetooth stops working. |
| 2 | BACK/V- | Previous/Decrease volume | Short press: Previous song Long press: Turn down the volume. | |
| 3 | NEXT/V+ | Next /Turn up the volume | Short press: next song Long press: Turn up the volume, note that there will be a beep sound when the volume is adjusted to the end | |
| 4 | PLAY/STOP | Play/pause, Answer/Hang up | During Bluetooth music playback, short press to control music playback or pause. When the phone calls, short press to connect the phone, and short press again to hang up. | |
| Interface | 5 | MICRO USB Power | MICRO USB power supply 5V | It can also be powered through the back pad 5V and GND wire. |
| 6 | B+ B- | Lithium battery powered | Really realize charging and discharging at the same time, the battery can be directly charged through the USB power supply. Bluetooth can continue to work normally during charging. (B+ B- do not reverse) | |
| 7 | Headphone jack | 3.5MM audio output/call sending | The factory default is soldered on the Microphone, and the onboard MIC sends the call. Note that the pads in the two boxes cannot be tinned at the same time. If the headset does not have a microphone, the audio connector is a three-segment layer, and the solder pad on the back of the module Microphone box is tin. At this time, the onboard MIC sends a message. If the earphone is equipped with a microphone, that is, the audio connector is a four-segment layer, the tin is placed on the pad in the Earphone box on the back of the module. At this time, the microphone on the on-board headset sends a message. | |
| 8 | Microphone |