Clear Acrylic Raspberry Pi 5 Case(C), Fully closed case, Supports the Pimoroni NVMe board and Off...

Clear Acrylic Raspberry Pi 5 Case(C), Fully closed case, Supports the Pimoroni NVMe board and Off...

New 33 available
Indicative market price: R178.51
R162.28
Shipping
R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate
The seller has indicated that they will usually have this item ready to ship within 2 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Seller
Buyer protection
Get it now, pay later

Product details

Condition
New
Location
South Africa
Product code
3365
Bob Shop ID
613701159
This case was designed for the Raspberry Pi 5 board with space to install the Pimoroni NVMe Base and  Official Active Cooler (The Raspberry Pi 5 board, NVMe Base and Active Cooler are NOT Included)


This DIY case requires assembly. You will need a small precision flathead screwdriver.(Included)

Clear 3mm Acrylic Panels to protect your Raspberry Pi 5.

Features

Openings For

  • 40PIN GPIO
  • PCIe
  • DSI/CSI Interfaces
  • Wall mounting holes
  • Airflow Vents On The Top And Front
  • With Power On/Off Button
  • Pull & Plug TF Card On The Bottom
 

What's in the box?

1 x PI5 Acrylic Case A
1 x Nonskid rubber pad (4PCS)
1 x Screwdriver
1 x Screws and standoffs pack

Resources

Installation Instructions

1.With the pishop.co.za logo facing down, push the four 20mm screws through the holes facing up. Each screw gets an acrylic 3mm spacer.

2. Install your SSD on the NVMe Base and slide it onto your acrylic base. Use the four black standoffs you received with your NVMe Base to hold your base in place.

3. It would be a good idea to mount the Active Cooler onto your Raspberry Pi 5 board before sliding it onto your base. Connect your NVMe ribbon cable to the Raspberry Pi board.

4. Use the four 18mm brass standoffs to secure the Raspberry Pi 5 board in place.

5. Install the 4 acrylic sides. Don't forget to slide the button into it's place.

6. Add the top and secure it with the four 6mm screws. It can be a bit tricky lining up all the holes.

Note: Stock is currently available in South Africa for national shipping!
Add to cart

Recently viewed

See more
41% OFF
4-Port High Quality USB2.0 High Speed Hub with LED Indicator and Switch (Black)..!
New
R76.50 R130.00
Laser Pointer Pen with Stylus
New
R162.73
Tapered Drum Lampshade with Geo Print Material | S133
New
R235.00
8% OFF
Transcend TS512MLK64V3N U-DIMM Memory Module 4GB DDR3 1333Mhz
New
R1,100.00 R1,200.00

Similar products

9% OFF
WS Pioneer600 Raspberry Pi Expansion Board
New
R579.89 R637.88
9% OFF
Metal Case (A) for Raspberry Pi Compute Module 4 IO Board with Cooling Fan
New
R278.29 R306.12
9% OFF
Overall Evaluation Board for Raspberry Pi Pico
New
R1,101.88 R1,212.07
9% OFF
Mini Base Board (A) designed for Raspberry Pi Compute Module 5
New
R423.81 R466.19