This item has closed 1 buyer bought 1 item
View other items offered by JustCheaper548

Similar products

4pcs 18pin Signal Data Cable for Bitmain Antminer Miner S9 S7 L3
R304.00
Standard Heatsink Customer Install
R710.00
1200w 1600w Output Wire 10 Pin for Bitmain Antminer Apw7 + Apw3 Psu
R402.00
5pcs 18pin Signal Cable for Antminer S9 S7 L3+ Machine,spacing 2.0mm
R361.00
Custom Antminer D3 Firmware NO FEE Custom Antminer D3 Firmware NO FEE Custom Antminer D3 Firmware NO FEE
Custom Antminer D3 Firmware NO FEE Custom Antminer D3 Firmware NO FEE Custom Antminer D3 Firmware NO FEE
Sold

Custom Antminer D3 Firmware NO FEE

7 were available / new
R200.00
Shipping
R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate
The seller has indicated that they will usually have this item ready to ship within 3 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Buyer protection
Get it now, pay later

Product details

Condition
New
Location
South Africa
Product code
D3soft
Bob Shop ID
354187339

Custom Antminer D3 Firmware NO FEE


Benefits:
No disconnecting from pools to run 1.5% dev fee.
Now you can get rid of hardware errors. This firmware allows you to control EACH boards voltage AND frequency. Good for dodgey chips and beat up machines.
Underclock & Overclock your Antminer D3.
By reducing the overall voltage to 9 or 10 volts you an save upto 50% on your electricity bill.
Control noise and heat whenever you want by adjusting settings up and down.
Makes your ROI better.
Can reboot your machine if your hashrate gets to low or you have to many hardwares.

Possible to go back to old firmware.

Based on Blissz Version 1.12. FINAL UPDATE.

Helpful links:
Installation, search Youtube for: Antminer D3 Firmware Upgrade / Blissz no HW Errors
Best settings, Youtube: D3 Antminer - Blissz Custom Firmware and Profit vs Power Cost

If you are reading this, you should know what Blissz firmware is about. I have added my own mods to it and it’s now very clean and stable.

Buying this mod:
Voids your warranty.
No warranty has been expressed or implied.
My D3's are running in perfect condition now. This is what you have been looking for, so be careful what other firmware you install.
Always start with your fans on Manual and 100% while you mess around finding the best settings then reduce as needed.

Firmware will be emailed within 24 hours of payment.
THIS FIRMWARE IS NOT FOR RESALE.

TAGS:

CUSTOM ANTMINER D3 FIRMARE NO DEV FEE

BLISSZ ANTMINER D3 FIRMWARE

BLISSZ ANTMINER D3 FIRMWARE FREE
 

Recently viewed

See more
50% OFF
Front Facing Camera Module Parts for Nokia Lumia 1020
R201.00 R401.00
Contact block n/o for np2 np2-be101
R43.57
84% OFF
GERMANY DDR 1980 - Geological Investigations FULL SET - FINE CTO USED
R12.00 R75.00
ESSENTIAL PATTERNS E95 `THE HOLIDAY COLLECTION` SIZES 10 - 20
R5.00