This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1715
DasMikro Programmable Sound Unit for Orlandoo F150 OH35P01 KIT Micro RC Crawlers
New
R844.00
Closed
11 May 24 00:19
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
612431799
Programmable?Sound Unit for Orlandoo F150 OH35P01 KIT Micro RC Crawlers?
Description:
This soundunit is developed specially for electric powered RC.
It could be used to 1:35, 1/24 and 1/18 RC crawlers. Especially suitable for Orlandoo F150 OH35P01 KIT Assemble Climbing RC Car Parts Version
Features: ??Plug and Play? ??Soundquality 22KHz ??Internal 1W amplifier at 8 Ohm speakers ??All connections done by plugs, no solderwork necessary ??Receiver signals are used for speed information, ?this allows brushless or DC Motor usage ??Fully assembeled in SMD technology (no heavy, vibration sensitive components) ??All wires included ??Very little dimensions and weight Technical Datas: Dimensions: 11 x 23,5 x 3,2mm (min.11x16x3,2mm) Voltage: 3V to 5V (supplied by the receiver) Note the maximum supply voltage of 5V! Current: app. 10mA without sound, app. 250mA at max. volume Speaker: 8-32 Ohm Output power: 1W at 8-Ohm at 5V; 0,6W at 8-Ohm at 3V Proportional inputs: Positive Impuls 0,8ms bis 2,0ms Soundquality: up to 22,05 kHz ? Teaching the sound unit for throttle idle/accelerate point: 1. Power on transmitter and receiver. LED blinks fast -> normal mode. Bring throttle stick to idle. Motor must not move. 2. Bridge study switch for about 0.5 seconds until beep -> LED cont. on. At this moment the idle position of the throttle stick is stored. 3. Move throttle stick to your desired acceleration point (throttle stick position where idle dead band stops and engine running sound starts) and wait for a beep. Now the dead (neutral) band of the speed channel is defined. 4. Move the throttle stick to full speed position and wait for three beeps. After this the sound unit is back in the normal operation mode.
Description:
This soundunit is developed specially for electric powered RC.
It could be used to 1:35, 1/24 and 1/18 RC crawlers. Especially suitable for Orlandoo F150 OH35P01 KIT Assemble Climbing RC Car Parts Version
Features: ??Plug and Play? ??Soundquality 22KHz ??Internal 1W amplifier at 8 Ohm speakers ??All connections done by plugs, no solderwork necessary ??Receiver signals are used for speed information, ?this allows brushless or DC Motor usage ??Fully assembeled in SMD technology (no heavy, vibration sensitive components) ??All wires included ??Very little dimensions and weight Technical Datas: Dimensions: 11 x 23,5 x 3,2mm (min.11x16x3,2mm) Voltage: 3V to 5V (supplied by the receiver) Note the maximum supply voltage of 5V! Current: app. 10mA without sound, app. 250mA at max. volume Speaker: 8-32 Ohm Output power: 1W at 8-Ohm at 5V; 0,6W at 8-Ohm at 3V Proportional inputs: Positive Impuls 0,8ms bis 2,0ms Soundquality: up to 22,05 kHz ? Teaching the sound unit for throttle idle/accelerate point: 1. Power on transmitter and receiver. LED blinks fast -> normal mode. Bring throttle stick to idle. Motor must not move. 2. Bridge study switch for about 0.5 seconds until beep -> LED cont. on. At this moment the idle position of the throttle stick is stored. 3. Move throttle stick to your desired acceleration point (throttle stick position where idle dead band stops and engine running sound starts) and wait for a beep. Now the dead (neutral) band of the speed channel is defined. 4. Move the throttle stick to full speed position and wait for three beeps. After this the sound unit is back in the normal operation mode.