DC-DC Step Down Adjustable Constant Voltage Current Power Supply Module
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615105214
Module parameters:
Scope: High-power LED constant current driver, rechargeable lithium batteries (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charging, solar panels, wind generators
Input voltage: 7-40V
Output voltage: continuously adjustable (1.25-35V) (applied to the input voltage is higher than the output voltage applications can boost)
Output Current: 8A, 10A maximum time within the (power tube temperature exceeds 65 degrees, please add cooling fan, 24V 12V 5A turn within generally be used at room temperature without a fan)
Constant Range: 0.3-10A (adjustable) module over 65 degrees, please add fan.
Turn lights Current: current value * (0.1), turn the lamp current and constant value linkage, such as constant value of 3A, turn the lamp current is set to a constant current of 0.1 times (0.1 x 3A = 0.3A), when the constant 2A, when adjusted to the current value, then turn the lamp current constant current of 0.1 times (0.1 x 2A = 0.2A).
This version is a fixed 0.1 times (actually turn the lamp current value is probably not very accurate) is full of instructions for charging.
Minimum pressure: 1V
Conversion efficiency: up to about 95% (output voltage, the higher the efficiency)
Operating frequency: 300KHZ
Output Ripple: about the ripple 50mV (without noise) 20M bandwidth (for reference) Input 24V Output 12V 5A measured
Operating temperature: Industrial grade (-40 a?? to + 85 a??) (please note the actual use of the power tube temperature, the temperature is too high, please enhance heat dissipation)
No-load current: Typical 20mA (24V switch 12V)
Load regulation: ± 1% (constant)
Voltage Regulation: ± 1%
Constant accuracy and temperature: the actual test, the module temperature changes from 25 degrees to 60 degrees, the change is less than 5% of the current value (current value 5A)
Dynamic response speed: 5% 200uS
Potentiometer adjustment direction: clockwise (increase), counterclockwise (decrease)
Indicator: color indicator, charging indicator light red, fully charged light green (no load is green)
Output short circuit protection: Yes, constant current (constant current setting values)
Input reverse polarity protection: None,
Output anti-anti-perfusion: no, for charging the battery needs additional two diodes!
Connection: Terminals
Package included:
1 x?DC-DC Step Down Adjustable Power Supply Module
, 
Scope: High-power LED constant current driver, rechargeable lithium batteries (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charging, solar panels, wind generators
Input voltage: 7-40V
Output voltage: continuously adjustable (1.25-35V) (applied to the input voltage is higher than the output voltage applications can boost)
Output Current: 8A, 10A maximum time within the (power tube temperature exceeds 65 degrees, please add cooling fan, 24V 12V 5A turn within generally be used at room temperature without a fan)
Constant Range: 0.3-10A (adjustable) module over 65 degrees, please add fan.
Turn lights Current: current value * (0.1), turn the lamp current and constant value linkage, such as constant value of 3A, turn the lamp current is set to a constant current of 0.1 times (0.1 x 3A = 0.3A), when the constant 2A, when adjusted to the current value, then turn the lamp current constant current of 0.1 times (0.1 x 2A = 0.2A).
This version is a fixed 0.1 times (actually turn the lamp current value is probably not very accurate) is full of instructions for charging.
Minimum pressure: 1V
Conversion efficiency: up to about 95% (output voltage, the higher the efficiency)
Operating frequency: 300KHZ
Output Ripple: about the ripple 50mV (without noise) 20M bandwidth (for reference) Input 24V Output 12V 5A measured
Operating temperature: Industrial grade (-40 a?? to + 85 a??) (please note the actual use of the power tube temperature, the temperature is too high, please enhance heat dissipation)
No-load current: Typical 20mA (24V switch 12V)
Load regulation: ± 1% (constant)
Voltage Regulation: ± 1%
Constant accuracy and temperature: the actual test, the module temperature changes from 25 degrees to 60 degrees, the change is less than 5% of the current value (current value 5A)
Dynamic response speed: 5% 200uS
Potentiometer adjustment direction: clockwise (increase), counterclockwise (decrease)
Indicator: color indicator, charging indicator light red, fully charged light green (no load is green)
Output short circuit protection: Yes, constant current (constant current setting values)
Input reverse polarity protection: None,
Output anti-anti-perfusion: no, for charging the battery needs additional two diodes!
Connection: Terminals
Package included:
1 x?DC-DC Step Down Adjustable Power Supply Module
,