Diamond blade seg.115 x 22.23mm for metal cutting

Diamond blade seg.115 x 22.23mm for metal cutting

New 849 available
R210.65
Shipping
R35.00 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30.00 surcharge. This will be calculated at checkout if applicable.
Check my rate
The seller has indicated that they will usually have this item ready to ship within 2 business days. Shipping time depends on your delivery address. The most accurate delivery time will be calculated at checkout, but in general, the following shipping times apply:
 
Standard Delivery
Main centres:  1-3 business days
Regional areas: 3-4 business days
Remote areas: 3-5 business days
Seller
Buyer protection
Get it now, pay later

Product details

Condition
New
Location
South Africa
Product code
TCDB70115
Bob Shop ID
638948009

Please note: 1 or more of the same item/s are shipped within a day or 2 - adding different items may mean delays in shipping due to items being from multiple suppliers/warehouses.


Diamond blade for metal cutting

TYPE:
Laser weld and segmented

DIAMETER: ø115mm
BORE: Ø22.23mm
MAX RPM: 13,300
USE: Metal cutting

What is a diamond blade?

A diamond blade is composed of a circular steel core and the diamond impregnated segments. The segments are seperated by slots in the core.

These slots assist in cooling the blade during operation by allowing water (wet cutting) or air (dry cutting) to flow between the segments. The segments or rims are a mixture of diamond powder and metal powders. The diamonds are industrial diamonds of different sizes and qualities depending on the material to be cut as well a the blade type.

How does a diamond blade work?

The individual diamond crystals exposed on the leading edge and the sides of the segment or rim carry out the cutting. The operator pushes the rotating blade into the material and the surface diamonds thus exposed mill a groove in the material. When the blade mills the material, the latter exerts wear on the blade. During cutting the exposed diamonds may crack or break. The material simultaneously starts to abrade the metal matrix, which releases more diamonds.

The more abrasive the material, the more rapid the tendency to wear down the matrix. Blades for cutting hard, denseless abrasive materials (such as tile, bricks, stone or cured concrete), require a softer metal matrix.

This will wear down faster, replacing the worn diamonds fairly quickly so that the blade continues to cut.

Blades for cutting soft, abrasive materials (such as green concrete and asphalt), must have  a hard, abrasion-resistant metal matrix in order to retain the diamonds for a longer time.

Water will prevent the blade from overheating:
It will greatly reduce the amount of harmful dust created by cutting. Remove the slurry from the cut, and extend the life of the blade.


Please note: 1 or more of the same item/s are shipped within a day or 2 - adding different items may mean delays in shipping due to items being from multiple suppliers/warehouses.

Add to cart

Recently viewed

See more
12% OFF
GUD CARTRIDGE HYDRAULIC Filter For VOLVO FM9 300 (D9A 12V 221KW) 02-07
New
R149.00 R169.00
AG1702 Air Filter Kia Rio Iii (GUD)
New
R309.60
E60 Fuel Pump (n52 Engine) - 5bar 6pin
New
R3,218.75
Children Lying Ring Baby Underarm Anti-Rollover Swimming Ring, Style: Water Elf (Large)
New
R548.00

Similar products

34% OFF
Tork Craft Diamond Blade Seg.230X22.23Mm Metal Cutting -
New
R589.00 R889.00
Diamond blade cont.rim 230x22.22mm pinnacle
New
R197.67
36% OFF
Tork Craft Diamond Blade Segm. 115Mm Reinf.Concrete -
New
R89.00 R139.00
Diamond blade seg.230x22.23mm metal cutting
New
R539.04