DM6F 2.4G 6CH DMSS Parkflyer Receiver For JR XG6 XG7 XG8 XG11 Transmitter
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 12 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615156722
Redcon DM6F 2.4G 6CH DMSS Parkflyer Receiver For JR XG6 XG7 XG8 XG11
Description:
The DM6F DMSS 6CH park-flyer receiver is designed for use with the JR XG series transmitters. It will bind with the JR XG6, XG7, XG8 and XG11 transmitters. It features full 6CH functionality and even sends back telemetry info (receiver voltage) to the transmitter.
Specification:
Brand Name: Redcon
Item Name: DM6F receiver
Band: 2.4GHz?
Channel: 6
Modulation: DMSS
Working Voltage: 3.6 a?? 9.6v
Weight: 4g
Antenna Length Main RX: 170mm?
Dimensions (W x Lx H): 18.5x 43.5x 9.5mm
Compatibility: JR XG6, XG7, XG8 and XG11
Application:? Special for small electric and non-power airplanes, for electric helicopters up to 450 size.
Note: Not for use in Nitro and Large electric airplanes and helicopters.
Features:
Compact and lightweight - only 4.9g!
Full function 6CH receiver
Compatible with JR DMSS radio systems
In-built receiver voltage telemetry function
No bind plug required, automatic binding with transmitter
Binding Procedure:
The receiver must be bind with the transmitter before it will operate.
1, Connect the battery( or BEC/ ESC with BEC output) to Batt.channel and note the LED on the receiver should flashing, now, the receiver is on bind mode.
2, Power on the transmitter, and enter the BIND menu.(Checking manual of your transmitter,how to enter the BIND menu. )
3, Press the BIN button on the display. The system will connect within a few seconds. Once connected, the LED on the receiver will go solid, indicating the system is connected.
4, Exiting from the BIND menu, and then setting the failsafe according the function of your transmitter.(Please check failsafe function of your transmitter)
Caution:
- DO NOT stick or apply the receiver antenna to Carbon or Metal material directly, as it will drastically reduce the operating range.
- For receivers with multi-antennas, it is recommended that each antenna be applied at 90 degrees to each other.
- For receivers with single antenna, please apply the antenna far away from any carbon, metal or electronic equipment as possible.
- Make sure turning the transmitter first after binding when using your radio control system.
- Make sure setting failsafe after binding.
Package Included:
1x?Redcon DM6F receiver
, 
, 
Description:
The DM6F DMSS 6CH park-flyer receiver is designed for use with the JR XG series transmitters. It will bind with the JR XG6, XG7, XG8 and XG11 transmitters. It features full 6CH functionality and even sends back telemetry info (receiver voltage) to the transmitter.
Specification:
Brand Name: Redcon
Item Name: DM6F receiver
Band: 2.4GHz?
Channel: 6
Modulation: DMSS
Working Voltage: 3.6 a?? 9.6v
Weight: 4g
Antenna Length Main RX: 170mm?
Dimensions (W x Lx H): 18.5x 43.5x 9.5mm
Compatibility: JR XG6, XG7, XG8 and XG11
Application:? Special for small electric and non-power airplanes, for electric helicopters up to 450 size.
Note: Not for use in Nitro and Large electric airplanes and helicopters.
Features:
Compact and lightweight - only 4.9g!
Full function 6CH receiver
Compatible with JR DMSS radio systems
In-built receiver voltage telemetry function
No bind plug required, automatic binding with transmitter
Binding Procedure:
The receiver must be bind with the transmitter before it will operate.
1, Connect the battery( or BEC/ ESC with BEC output) to Batt.channel and note the LED on the receiver should flashing, now, the receiver is on bind mode.
2, Power on the transmitter, and enter the BIND menu.(Checking manual of your transmitter,how to enter the BIND menu. )
3, Press the BIN button on the display. The system will connect within a few seconds. Once connected, the LED on the receiver will go solid, indicating the system is connected.
4, Exiting from the BIND menu, and then setting the failsafe according the function of your transmitter.(Please check failsafe function of your transmitter)
Caution:
- DO NOT stick or apply the receiver antenna to Carbon or Metal material directly, as it will drastically reduce the operating range.
- For receivers with multi-antennas, it is recommended that each antenna be applied at 90 degrees to each other.
- For receivers with single antenna, please apply the antenna far away from any carbon, metal or electronic equipment as possible.
- Make sure turning the transmitter first after binding when using your radio control system.
- Make sure setting failsafe after binding.
Package Included:
1x?Redcon DM6F receiver
, ,