This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1654
Similar products
Electronic Competition Kit ON-OFF Test Circuit and Waveform Output Kit Overhaul Board Fault Board Co
New
R544.00
Closed
11 May 24 00:05
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Buyer Protection
How you're covered
Get it now, pay later
Returns
Product information
Condition:
New
Location:
International
Bob Shop ID:
612373443
Electronics assembly:
This is a display and waveform output circuit composed of an on-off test circuit and a single-chip computer control. The function of the continuity test circuit is used to judge the continuity and short circuit of the transformer coil. If the test terminal J1 is open, the horn will not sound. If the coil is on, the horn will sound, so you can quickly judge. If the coil resistance is less than a certain value, we can consider that there is a short circuit inside the coil, and the continuity test circuit can judge and prompt with a higher frequency sound. The judgment point of the short circuit state can be adjusted by W1.
The single-chip computer-controlled display and waveform output circuit can change four states under the control of a button.
Note that in this circuit assembly, J1 is two test terminals, and two wires with clips are directly soldered to the circuit board. The horn is fixed on the circuit board with a wire.
Commissioning and testing:
1. The status of the MCU part
1) Power on, D4? ~ D11 flashing. This is the initial state.
2) Press K1, D4 is on, the rest are off. This is the ON-off test state.
3) Press K1 again, half on and half off. This is the waveform output 1 state.
4) Press K1 again, all lights up. This is the waveform output 2 state.
5) Press K1 again, the flowing water flashes. Back to the original state.
2. Test and record
1) Use 5V DC power. After the power is turned on, it should enter the initial state.
2) J1 is connected to a 560?? resistor, and the speaker should sound, indicating that the terminal under test is connected.
Package included
1 x ON-OFF Test Circuit and Waveform Output Kit
This is a display and waveform output circuit composed of an on-off test circuit and a single-chip computer control. The function of the continuity test circuit is used to judge the continuity and short circuit of the transformer coil. If the test terminal J1 is open, the horn will not sound. If the coil is on, the horn will sound, so you can quickly judge. If the coil resistance is less than a certain value, we can consider that there is a short circuit inside the coil, and the continuity test circuit can judge and prompt with a higher frequency sound. The judgment point of the short circuit state can be adjusted by W1.
The single-chip computer-controlled display and waveform output circuit can change four states under the control of a button.
Note that in this circuit assembly, J1 is two test terminals, and two wires with clips are directly soldered to the circuit board. The horn is fixed on the circuit board with a wire.
Commissioning and testing:
1. The status of the MCU part
1) Power on, D4? ~ D11 flashing. This is the initial state.
2) Press K1, D4 is on, the rest are off. This is the ON-off test state.
3) Press K1 again, half on and half off. This is the waveform output 1 state.
4) Press K1 again, all lights up. This is the waveform output 2 state.
5) Press K1 again, the flowing water flashes. Back to the original state.
2. Test and record
1) Use 5V DC power. After the power is turned on, it should enter the initial state.
2) J1 is connected to a 560?? resistor, and the speaker should sound, indicating that the terminal under test is connected.
Package included
1 x ON-OFF Test Circuit and Waveform Output Kit