FlySky FS-BS4 2.4GHz 4CH ASHDS 2A RC Receiver PWM/PPM/I.bus/S.bus Output with Gyroscope Function for
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 12 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615149466
FlySky FS-BS4 2.4GHz 4CH ASHDS 2A RC Receiver PWM/PPM/I.bus/S.bus Output with Gyroscope Function for RC Car Boat
OVERVIEW:
FlySky FS-BS4, a gyro-embeded receiver, has 4 channels. In addition to the regular functions, it can also be used with a transmitter with S.V.C. (Smart Vehicle Control) function to realize a smart control over the car and make sure the car travels in the expected direction even on bumpy/slippery surfaces, or during cornering.
Specification: Brand Name: FlySky Item Name: FS-BS4 Receiver Dimensions: 35.4 * 29.6 * 13mm? Weight: 20g? PWM channels: 4CH Wireless frequency: 2.4GHz? Wireless protocol: AFHDS 2A? Range: 100 - 300m (ground)? Antenna type: single antenna (150mm)? Power: 4.0-6.5V? RSSI: Supported? Data port: PWM / PPM / i.bus / s.bus? Temperature range: -10 a?? a?? + 60 a??? Humidity range: 20% -95%? Online Update: Yes? Certification: CE
? Binding: 1.? Turn on the transmitter, check the RF standard and if necessary, change it to [AFDHS 2A 2-way]. For detailed instructions, refer to the transmitter's manual. 2.? Set the transmitter to bind mode. For detailed instructions, refer to the transmitter's manual. 3.? Make sure the receiver is powered off. 4.? Connect the bind cable to the BIND/VCC port on the receiver. Then connect the power to any other ports on the receiver. The red indicator starts to flash rapidly, indicating that the receiver is in bind mode. 5.? Wait till the indicator stops flashing, which means binding is finished. 6. Disconnect the bind cable and power from the receiver. Then connect the power to the BIND/VCC port. 7.? Check if all the servos work as expected. If anything does not work as expected, restart this procedure from the beginning.
Package Included:
1 x?FS-BS4 Receiver
OVERVIEW:
FlySky FS-BS4, a gyro-embeded receiver, has 4 channels. In addition to the regular functions, it can also be used with a transmitter with S.V.C. (Smart Vehicle Control) function to realize a smart control over the car and make sure the car travels in the expected direction even on bumpy/slippery surfaces, or during cornering.
Specification: Brand Name: FlySky Item Name: FS-BS4 Receiver Dimensions: 35.4 * 29.6 * 13mm? Weight: 20g? PWM channels: 4CH Wireless frequency: 2.4GHz? Wireless protocol: AFHDS 2A? Range: 100 - 300m (ground)? Antenna type: single antenna (150mm)? Power: 4.0-6.5V? RSSI: Supported? Data port: PWM / PPM / i.bus / s.bus? Temperature range: -10 a?? a?? + 60 a??? Humidity range: 20% -95%? Online Update: Yes? Certification: CE
? Binding: 1.? Turn on the transmitter, check the RF standard and if necessary, change it to [AFDHS 2A 2-way]. For detailed instructions, refer to the transmitter's manual. 2.? Set the transmitter to bind mode. For detailed instructions, refer to the transmitter's manual. 3.? Make sure the receiver is powered off. 4.? Connect the bind cable to the BIND/VCC port on the receiver. Then connect the power to any other ports on the receiver. The red indicator starts to flash rapidly, indicating that the receiver is in bind mode. 5.? Wait till the indicator stops flashing, which means binding is finished. 6. Disconnect the bind cable and power from the receiver. Then connect the power to the BIND/VCC port. 7.? Check if all the servos work as expected. If anything does not work as expected, restart this procedure from the beginning.
Package Included:
1 x?FS-BS4 Receiver