R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable. Check my rate
Free collection from
Duncanville, Vereeniging
The seller allows collection for this item and will be in contact with the full collection address once the order is ready.
Ready for collection by Tuesday, 14 May.
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 3 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Fujikura FSM-50S Fusion Splicer with protective case
Automatic Fibre splicer This is core aligning arc fusion splicer. FSM-50S Features Fully automatic core alignment with 9 second splice time for SM fiber Reduced splice protector shrink time now only 35 seconds Extremely compact and lightweight just 2.8kg Automatic fibre type identification Multi-position monitor for front or top mounting High capacity battery option for 120 splice/shrink cycles Real time arc calibration Fibre clamps integrated into wind protector to reduce operation time Dual-directional operating system The reversible monitor accommodates the user's ergonomic preference. With a control panel on each side, the ease of use is phenomenal.
Splice time of 9 sec. Improved computer processing and newly introduced stepping motor help achieve 9 sec. splice time with SM fiber.
Tube-heat time of 35 sec. Advanced heater design shortens tube-heat time to 35 sec. with FP-03 protection sleeve.
Arc calibration-free system Time-consuming arc calibration is no longer requried with real- time arc calibration.
Specifications:
Applicable fibers SMITU-T G.652, MMITU-T G.651, DSITU -T G.653, NZDSITU-T G.655 Fiber Count Single Cladding diameter 80 to 150m Coating diameter 100 to 1000m Fiber cleaved length 8 to 16mm with coating diameter of 250m or less. 16mm with coating diameter of 250 to 1000m. Optional set-plate for 8 to 16mm with coating diameter of 250 to 1000m is available. Actual average splice loss 0.02dB with SM, 0.01dB with MM, 0.04dB with DS, 0.04dB with NZDS. Measured by cut-back method relevant to ITU-T and IEC standards. Splice time Typical 9sec. with standard SM fiber Return loss >>60dB Splicing modes 40 user programmable modes and up to 60 modes for referencefactory predetermined setting Splice loss estimate Available Attenuation splice function Intentional high splice loss of 0.1dB to 15dB0.1dB stepcan be made for an in-line fixed attenuator. Storage of splice result The last 2000 results to be stored in the internal memory Fiber display X / Y, or both X and Y simultaneously Magnification 295x for single X or Y view, or 147x for X and Y view. Viewing method Two CMOS cameras and 5.6 inch color LCD monitor. Operating condition 0 to 5000m above sea level, 0 to 95% RH and -10 to 50 respectively. Mechanical proof test 2Nstandard/ 4.4Noption Tube heater Built - in tube heater with 10 heating modes and up to 20 modes for reference Tube heat time Typical 35sec. with FP-03 protection sleeve Applicable protection sleeve length 60mm, 40mm and a series of micro sleeves No.of splice/heating with battery Typical 80 cycles with BTR-06S/ Typical 160 cycles with BTR-06L Power supply Auto voltage selection from 100 to 240Va.c. or 10 to 15Vd.c. with ADC-11. 13.2Vd.c. with BTR-06S / L. Terminals USB 1.1USB-B typefor PC communication. Video terminal RCA video jack / NTSC Wind protection Max. wind velocity of 15m/s Dimensions 150W x 150D x 150H (mm)