JCD 908S 220V 80W Adjustable Temperature Electric Soldering Iron Heater Ceramic Internal Heating Ele
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615090770
Specification:
Brand Name: JCD Dimensions: Lenght 70mm Diamter 3.8mm Temperature Stability: Adjustable Input Voltagle: AC220V Output Power: 80W Output Temperature: 200a??-450a??
Soldering Iron Manual
1. Always keep the tip of the bit clean, ensure to coat the bit liberally with solder the first time the iron is switched on. Note: Initial tinning is done in order to extend the life of the bit. 2. Wet the provided sponge prior to using. 3. Check that the solder wire is ready for use and adequately extended from the case as shown in step 1 in the above illustration below. 4. Ensure that the bit fits snugly and has adequate contact with the internal element.
Using the soldering iron? 1. After turning the iron on, the bit will commence heating and will be ready for use when the solder wire begins to meltt at contact. 2. Initiate soldering by ensuring the meltted solder makes a clean connection between the contacts that you attempting to solder.? 3. Move the solder wire and iron away once enough solder is placed and wipe any residual solder using the wet sponge. 4. Always remember to switch the iron off at the mains and place it in the provided holder while it cools enough to be stored safely.
Notes:? 1. Use safety goggles and take necessary precautions to avoid injury or fire. 2. The iron heats up quickly. Select a suitable temperature to operate at. Using the iron for long hours and at high temp may shorten the life of the product.? 3. Make sure to only switch the iron on when required and switch it off when not, in order to reduce the risk of injury and fire. 4. Clean the soldering tip ever so often to extend its life. Avoid using abrasive chemicals and surfaces as this could damage the metallic surface. 5. The provided bits are 900M series and spares are available from where you purchased this product.
Package included:
1 x Soldering Iron Heater?
Details Pictures:
Brand Name: JCD Dimensions: Lenght 70mm Diamter 3.8mm Temperature Stability: Adjustable Input Voltagle: AC220V Output Power: 80W Output Temperature: 200a??-450a??
Soldering Iron Manual
1. Always keep the tip of the bit clean, ensure to coat the bit liberally with solder the first time the iron is switched on. Note: Initial tinning is done in order to extend the life of the bit. 2. Wet the provided sponge prior to using. 3. Check that the solder wire is ready for use and adequately extended from the case as shown in step 1 in the above illustration below. 4. Ensure that the bit fits snugly and has adequate contact with the internal element.
Using the soldering iron? 1. After turning the iron on, the bit will commence heating and will be ready for use when the solder wire begins to meltt at contact. 2. Initiate soldering by ensuring the meltted solder makes a clean connection between the contacts that you attempting to solder.? 3. Move the solder wire and iron away once enough solder is placed and wipe any residual solder using the wet sponge. 4. Always remember to switch the iron off at the mains and place it in the provided holder while it cools enough to be stored safely.
Notes:? 1. Use safety goggles and take necessary precautions to avoid injury or fire. 2. The iron heats up quickly. Select a suitable temperature to operate at. Using the iron for long hours and at high temp may shorten the life of the product.? 3. Make sure to only switch the iron on when required and switch it off when not, in order to reduce the risk of injury and fire. 4. Clean the soldering tip ever so often to extend its life. Avoid using abrasive chemicals and surfaces as this could damage the metallic surface. 5. The provided bits are 900M series and spares are available from where you purchased this product.
Package included:
1 x Soldering Iron Heater?
Details Pictures:
