| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
LAUNCH X431 PRO Elite is a new release (August 2023) with the tablet and functions of the X431 PRO 5th Gen, at a very attractive price, but with OBD diagnostic cable instead of Bluetooth connector, and 2 Years Updates included.
1. ABS Bleeding. When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.
2. TPMS Reset. When the tire pressure is too low, the tire leaks, the tire pressure monitoring device is replaced or installed, the tire is replaced and the tire pressure sensor is damaged, The tire pressure resetting function must be performed to reset tire pressure and turn off the tire pressure MIL.
3. Oil Lamp Reset. Allows you to perform a reset for a new calculation of Engine Oil life system once changed the oil.
4. Electronic Throttle Sensor Reset. To utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state.
5. Injector Coding. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identify injectors to accurately control fuel injection.
6. SAS Reset. It helps clear the faulty steering angle sensor memories to reset the steering angle and plays an important role in the steering angle sensor calibration.
7. Brake-pad Reset. To deactivate and activate the brake control systems, assist with brake fluid control, open and close brake pads, and set brakes after disc or pad replacement.
8. Gear Learning. Perform gear learning for the car when the engine ECU, the crankshaft position sensor, or the crankshaft flywheel is replaced.
9. IMMO Service. To prevent the car from being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.
10. Battery Matching. Enables you to perform a resetting operation on the monitoring unit of the battery, in which the original low battery fault information will be cleared.
11. DPF Regeneration. It is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode. Specially works for Diesel Particulate Filter systems with DPF.
12. EGR Adaption. This function is used to learn the EGR (Exhaust Gas Recirculation ) valve after it is cleaned or replaced.
13. Suspension Matching. When replacing the body height sensor in the air suspension system, or control module or when the vehicle level is incorrect, this function can adjust the body height sensor for level calibration.
14. NOx Sensor Reset. If the NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECU.
15. Tyre Reset. This function is used to set the size parameters of the modified or replaced tire.
16. Windows Calibration. This feature is designed to perform door window matching to recover ECU initial memory.
17. Stop-start Reset. This function is used to open or close the automatic Start/Stop function via setting the hidden function in ECU (The precondition is the vehicle equipped with hidden function and hardware support)
18. AC Initialization. AC system relearn/initialization must be performed when the vehicle AC ECU or actuator is replaced or the ECU memory is lost.
19. AdBlue Reset. After the diesel exhaust treatment fluid (car urea) is replaced or filled up, the urea reset operation is required.
20. AFS Headlamp Reset. This function enables you to initialize the adaptive headlamp system.
21. A/F Reset. This function is applied to set or learn air/fuel rate parameters.
22. Gearbox Reset. This function enables you to complete the gearbox self-learning to improve gear-shifting quality
23. Coolant Bleeding. Use this function to activate the electronic water pump before venting the cooling system.
24. Transport Reset. To lower vehicle power consumption, the user may perform the following operations: limit vehicle speed, not wake up the network for the door open and disable the remote key, etc. In this case, deactivating the transport mode is needed to recover the vehicle being normal.
25. Seat Calibration. This function is applied to match the seats with memory functions that are replaced and repaired.
26. High Voltage Battery Detection. This function is used for high-voltage battery diagnosis and status information detection.
27. Sunroof Initialization. This function enables you to set the sunroof to lock off, closed it when it rains, sliding/tilting the sunroof memory function, temperature threshold outside the car, etc.
28. Engine Power Balance Monitoring This function is used to monitor crankshaft acceleration in the power stroke of each cylinder, to determine the relative power provided by each cylinder.
29. Language Change This function is used to change the system language of the vehicle center console. note: you need to have a language pack to do a language change
30. Gas Particulate Filter (GPF) RegenerationThis function is used to perform the GPF replacement or regeneration after the fuel consumption is increased and engine output power is reduced resulting from a long time service of the GPF.
31. Intelligent Cruise Control System ResetThis function is used to match the intelligent cruise control module after it is replaced or repaired.
32. Reset Program (Extension)(Note: Available maintenance functions vary depending on the vehicle make, year, and model.)
33. NEW Function - GPF Generation:GPF (Gasoline Particulate Filter) diagnostics primarily involve monitoring the filter's pressure differential and temperature to assess soot accumulation and ensure effective regeneration.
