LED 7-15W Thyristor Dimming Driving Power Supply Module for Ceiling Lamp Panel Light Downlight
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615107158
Features:
1. Non-isolated output, high-power LED dimming driver, please pay attention to the safety of use, and the housing is electrically insulated. 2. The F7-15X1W driver is designed for dimming 7-15 1W high-power LED lamps, and the lamp beads must be connected in series. 3.Open circuit protection:?no-load power consumption 1.2/0.3W (long-term open circuit output is not recommended to avoid damage to the protection components) 4.High temperature protection:?if the temperature of the power supply exceeds 150?ﾣC, the output will be turned off, and the output will be restored when the temperature drops to 90?ﾣC.
Technical Parameters:
Product model: F7-15W non-isolated dimming driver Input voltage: 85~265V/AC Input?frequency: 50/60Hz Input current: 0.12A or 0.23A Inrush current: 2A (500nS) Power factor: 0.6 Power efficiency: 88% Output voltage: 20~49V Output current: 200-280/150-280mA Ambient temperature: -20a??~ +45a?? Environmental humidity: 20~ 50% RH Bare board size: 51 x 21 x 18 MM Weight: 50 g Input wiring: external_brown (live wire L), blue (zero wire N); built-in_white (live wire L); white (zero wire N) Output wiring: external_red (positive +), black (negative-); built-in_red (positive +), white (negative-)
Quality Assurance: This thyristor dimming light comes from the date of manufacture, not due to water, dampness or short circuit of the shell, etc., one year replacement, two years warranty.
NOTE: For built-in use, it is forbidden to use heat-shrinkable tubing for insulation, it must be wrapped with insulating paper, and vents must be left at the input and output ends to facilitate heat dissipation of the power supply. Note for use: This power supply is non-isolated, please connect the lamp and then power on, otherwise it will burn the lamp source! ! !
Package included:
1 x Dimming Driving Power Supply Module
1. Non-isolated output, high-power LED dimming driver, please pay attention to the safety of use, and the housing is electrically insulated. 2. The F7-15X1W driver is designed for dimming 7-15 1W high-power LED lamps, and the lamp beads must be connected in series. 3.Open circuit protection:?no-load power consumption 1.2/0.3W (long-term open circuit output is not recommended to avoid damage to the protection components) 4.High temperature protection:?if the temperature of the power supply exceeds 150?ﾣC, the output will be turned off, and the output will be restored when the temperature drops to 90?ﾣC.
Technical Parameters:
Product model: F7-15W non-isolated dimming driver Input voltage: 85~265V/AC Input?frequency: 50/60Hz Input current: 0.12A or 0.23A Inrush current: 2A (500nS) Power factor: 0.6 Power efficiency: 88% Output voltage: 20~49V Output current: 200-280/150-280mA Ambient temperature: -20a??~ +45a?? Environmental humidity: 20~ 50% RH Bare board size: 51 x 21 x 18 MM Weight: 50 g Input wiring: external_brown (live wire L), blue (zero wire N); built-in_white (live wire L); white (zero wire N) Output wiring: external_red (positive +), black (negative-); built-in_red (positive +), white (negative-)
Quality Assurance: This thyristor dimming light comes from the date of manufacture, not due to water, dampness or short circuit of the shell, etc., one year replacement, two years warranty.
NOTE: For built-in use, it is forbidden to use heat-shrinkable tubing for insulation, it must be wrapped with insulating paper, and vents must be left at the input and output ends to facilitate heat dissipation of the power supply. Note for use: This power supply is non-isolated, please connect the lamp and then power on, otherwise it will burn the lamp source! ! !
Package included:
1 x Dimming Driving Power Supply Module
