Mecer 1200VA 720W 12V Inverter - Setup InstructionsCOMPLUSORY SPECIAL INSTRUCTIONS TO FOLLOWThis inverter must be installed by a qualified electrician. Incorrectinstallation can result in electrical shock, damage to equipment, or fire. Theinverter will not power on until all required connections are properly made.What's IncludedMecer 1200VA / 720W Inverter Unit (12V DC)User ManualAC Input Power CableAC Output Sockets (on the unit)Cooling Fan (built-in)What You'll Need12V Deep Cycle Battery (minimum 100Ah recommended)12V Battery Cables (with correct gauge and terminals)Circuit breaker or fuse (recommended for DC side protection)Tools for electrical connections (used by the electrician)Installation Steps (By a Qualified Electrician Only)1. Choose a Safe LocationInstall indoors in a well-ventilated, dry, and cool space.Keep away from flammable materials and direct sunlight.2. Connect the BatteryEnsure the inverter ON/OFF switch is OFF.Connect the positive (+) terminal of the battery to the positive (+) DC input ofthe inverter.Connect the negative (-) terminal of the battery to the negative (-) DC input.Use correct polarity to avoid damage.Note: A fuse or circuit breaker should be installed between the battery andinverter on the positive cable for safety.3. Connect the AC Input (Optional)If you plan to use grid power to charge the battery via the inverter's built-incharger, connect the AC input to a suitable wall outlet or DB board via anisolator or dedicated breaker.4. Connect the AC OutputConnect essential appliances (TV, router, lights, etc.) to the AC output socketsor wire into an essential loads DB board.Do not exceed the 720W limit.5. Check ConnectionsDouble-check all connections: battery polarity, tightness of terminals, andgrounding if required.6. Power OnOnce all connections are complete and safe:Turn on the battery breaker (if used).Flip the inverter's power switch to ON.The inverter should now power on and begin supplying power or charging.NotesThe inverter will not turn on if the battery is not connected or is improperlyconnected.Never operate the inverter without a battery connected.This inverter is not designed to power high-load appliances like kettles,stoves, or heaters.Operation TipsRegularly check battery water levels (if using lead-acid).Keep ventilation ports clear of dust.Do not overload the inverter.Maintenance & SupportIf the unit emits continuous beeping or shows an error light, refer to the usermanual or contact a professional or Mustek Limited PTY LTD as the warranty isheld with Mustek South Africa.Do not open the unit yourself-risk of electric shock.xxPlease note that batteries are not included and needs to be boughtseparatelyxxThis unit is also intended for use with IT equipment and will not be able to runa kettle, heater or anything that uses a motor or an element.Features:- Simulated sine wave inverter- Built-in AVR for voltage regulation- Wide input voltage range: 90-280 VAC- 12VDC available- Overload and short circuit protection- LCD display for comprehensive informationSpecifications:- MODEL Mecer IVR-1200LBK- CAPACITY 1200 VA / 720 W- POWER FACTOR 0.8- Input Voltage range 90-280VACLine Mode:- Output Voltage- Bypass mode: 0utput voltage same as input voltage- AVR mode: Output voltage = Input voltage 1.2 at Input voltage - OutputFrequency Same as inputBattery Mode (BATTERIES NOT INCLUDED):- Output Voltage 230Vac +/-10%- Transfer Time 20ms typical- Waveform Modified Sine-waveOverload Capability:- Bypass Mode (in VA and Watts) Load >110%+/-15% , alarm 5 mins then fault- Load >130% +/-15%, fault immediately.- AVR Mode (in VA and Watts)at Input voltage > 170VAC Load >100%+/-15%, go tobypass mode- AVR Mode (in VA and Watts)at Input voltage 60%+/-15%, go tobypass mode- Battery Mode (in W) Load>110% +/-15%, overload alarm for 15s, and then willswitch to fault mode for 10s. Then unit will re-start for 5 times Load>120%+/-15% , fault & cut off O/P immediately.Short Circuit Protection:- Line Mode Breaker- Battery Mode Current limit +Firmware ProtectionBattery specs needed (NOT INCLUDED):- Battery Voltage 12VDC- Acceptable Battery Type Rechargeable lead-acid battery, Deep dischargebattery- This product is not capatible to Lithium-Ion- Polarity Reserve Protection Yes- Charger available I/P range 90 280VCharger:- Constant Current Charger Voltage 14.3VDC +/-2%- Floating Charge Voltage 13.7VDC +/-2%- Maximum Charge Current 10A or 20A- DC Start Voltage >11VDCPhysical:- Dimension, D X W X H (mm) 350 x 90 x 300- Net Weight (kgs) 4.5Environment:- Operating Humidity 0 to 90% Relative Humidity(Non-condensing)- Operating Temperature 0 degrees C to 40 degrees C- Storage Temperature -15 degrees C to 50 degrees C
