NEJE MASTER 3 Plus Laser Engraver with N40630 Laser Module(EU Plug)
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Product code
EDA003565401A
Bob Shop ID
593687648
1. Suitable for 600mm wide desktop, the left side of the machine is not limited by the material size. Suitable for processing large area materials. Under the protection of MEMS vibration protection sensor, the engraving and cutting process can be completed at the same time.
2. The X-axis motion module is only 120g, driven by a 40mm-thick high-performance stepper motor, bringing a faster engraving experience than the gantry structure.
3. 3400 x 5600 pixels, engraving accuracy: 0.075mm dot pitch, 339 dots/inch. The function test of the whole machine only needs 4 screws to complete the installation.
4. The newly designed N40630 module can cleanly cut 3mm thick plywood at one time, the minimum focus is 0.05x0.05mm, and the overlay can engrave metal. Built-in fast intelligent drive, timely temperature feedback, intelligent adjustment of fan cooling. Safe and quiet to use.
5. Wood, MDF, leather, paper, cotton, etc. are all supported. The blade is very clean. The finish spray can engrave stainless steel, glass, clear acrylic, etc.
6. 32-bit control system, the fastest speed can reach 200,000mm/min, support LaserGRBL, Lightburn, NEJE software, NEJE APP (Android, iOS, ipadOS, macOS)
7. You can take pictures with your mobile phone or choose pictures from the album.
Packing List:
Laser Engraver 1
Module 1
1 12V3A power supply
Euro Adapter 1
Manual 1
red glasses 1
(Data cable x1, wooden board x1, paper x5, pen x1, brush x1, focusing film x1, angle iron x4, aluminum oxide film x1, cable tie x3, nut x5, big hexagon wrench x1, small hexagon wrench x1, opening Wrench x1)
2. The X-axis motion module is only 120g, driven by a 40mm-thick high-performance stepper motor, bringing a faster engraving experience than the gantry structure.
3. 3400 x 5600 pixels, engraving accuracy: 0.075mm dot pitch, 339 dots/inch. The function test of the whole machine only needs 4 screws to complete the installation.
4. The newly designed N40630 module can cleanly cut 3mm thick plywood at one time, the minimum focus is 0.05x0.05mm, and the overlay can engrave metal. Built-in fast intelligent drive, timely temperature feedback, intelligent adjustment of fan cooling. Safe and quiet to use.
5. Wood, MDF, leather, paper, cotton, etc. are all supported. The blade is very clean. The finish spray can engrave stainless steel, glass, clear acrylic, etc.
6. 32-bit control system, the fastest speed can reach 200,000mm/min, support LaserGRBL, Lightburn, NEJE software, NEJE APP (Android, iOS, ipadOS, macOS)
7. You can take pictures with your mobile phone or choose pictures from the album.
Packing List:
Laser Engraver 1
Module 1
1 12V3A power supply
Euro Adapter 1
Manual 1
red glasses 1
(Data cable x1, wooden board x1, paper x5, pen x1, brush x1, focusing film x1, angle iron x4, aluminum oxide film x1, cable tie x3, nut x5, big hexagon wrench x1, small hexagon wrench x1, opening Wrench x1)