Nitro OBD2 Plug & Drive Performance Tuning Box, 35/25% more power/torque, DIESEL CARS *FREE DELIVERY

Nitro OBD2 is a Plug & Drive Ready device for increasing the performance of your engine. Nitro OBD2 is easy to install. Just plug it into the OBD2 connector in the car(under the dashboard). Nitro OBD2 fits all cars newer than the year of 1996 so long as they have a obd2 plug socket. It works based on OBD2 protocols and remaps the Car's computer ECU for optimum performance. After driving over 200 km Nitro OBD2 adjusts itself to the car, according to the drivers' habits and always keeps remapping the ECU to increase the optimum performance of the engine.

 

 

 

According to your driving habits, Nitro OBD2 makes a new map in the car's computer ECU to increase the performance of your car. As you drive more and more KM/Mile, it renews the map. Thus it keeps the vehicle's power and torque at the optimum setting.

 

 

 

Nitro OBD2 is a Chip Tuning Box which can be plugged into the OBD2 connector of your car to increase the performance of your car. When it  is plugged into OBD2 connector, Nitro OBD2 receives the information from the car computer ECU. With the received data from ECU, NitroOBD2 adjusts the boost pressure, quantity of fuel, injection timing and pressure to increase the performance of your car. NitroOBD2 Chip Tuning Box does not exceed the manufacturers requirements. It works only within the tolerance of the engine. NitroOBD2 finds out the hidden power of your car. NitroOBD2 does not damage the engine and the car computer ECU or not cause any negative effects to the car factory setting. NitroOBD2 does not change any of the settings permanently. To turn back to the car's original settings, just unplug NitroOBD2 from OBD2 connector.NitroOBD2 finds out the hidden power of your car.

 

 

 

1.Up to 35% more power 

2.Up to 25 % more torque

3.Nitro OBD2 is very easy to use

4.Plug Nitro OBD2 into OBD2 connector into your car, and turn the ignition on for 30 seconds and then turn the engine on.

5.Nitro OBD2 settings are optimal and the best for your car. Even the parameters are different for each vehicle, there might not be a need to make an additional adjustment

 

Nitro OBD2 works on the basis of changing the signal form ECU. As a consequence, it changes the whole injection map. The main difference between Nitro OBD2 Chip Tuning Box and Remapping tuning methods is that Nitro OBD2 Chip Tuning Box is easily removable, and after unplug you go back to the factory settings. Nitro OBD2 is the cheap and safe type of tuning. Remapping is a permanent change to your car. This is the expensive tuning and you cannot remove it. Nitro OBD2 is equipped with the engine protection function and 100% safe for your car engine. NitroOBD2 produced on the printed circuit board in SMD technology. Nitro OBD2 Chip Tuning Boxes are high quality.

 

 

 

1. Pull the Car Key out from the ignition

 

2. Find OBD2 connector(*) in your car and Plug in Nitro OBD2

 

3. Insert the key into the ignition and turn the key to the first stage. (Do not start the car)

 

4. Press the reset button for about 5 sec. After releasing the button, wait for 30-54 sec. (Nitro OBD2 will communicate and establish connection with ECU)

 

5. Start the engine

 

6. Nitro OBD2 will recognize your vehicle and your driving habits, after approximately 200 km/150 miles driving and thus Nitro OBD2 will adjust itself to match your car perfectly for more fuel saving.