This item has closed with no items sold
View the relisted Item
View the relisted Item
View other items offered by szulou1654
Similar products
Original Airbot OMNIBUS F4 V6 Flight Controller & Typhoon32 V2.1 35A Blheli_32 3-6S Brushless ESC
New
R1,940.00
Closed
11 May 24 00:18
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Buyer Protection
How you're covered
Get it now, pay later
Returns
Product information
Condition:
New
Location:
International
Bob Shop ID:
612428043
Original Airbot OMNIBUS F4 V6 Flight Controller & Typhoon32 V2.1 35A Blheli_32 3-6S Brushless ESC
Specification:
Flight Controller
OMNIBUS F4's upgrade version, using F405 and new target, with?5x UARTs?now.
classic OMNIBUS design, using F4 MCU controls OSD over SPI bus, compare the first version, we added BMP280 as barometer and SD Card supports.?OSD Configuration has been incl. in Betaflight GUI.?FC?incl. 5V1A BEC on board(3-6s) and 1x 8V BEC for Camera?MPU6000 at SPI bus, Ext, SPI for damped gyro ?Use fireworks v2 firmware, in?CLI,?set?gyro_to_use?=?SECOND
?New version with 8PIN Sh1.0 Socket, could be much easier connect to our 4in1 ESC by one cable.On v5, we added jumpers for Current source select, please?read the manual and set the jumper?before using the FC.
1 x Flight Cotnroller
1 x Brushless ESC
1 x?3CM 8pin cable
1 x?4CM FPC cable
Specification:
Flight Controller
OMNIBUS F4's upgrade version, using F405 and new target, with?5x UARTs?now.
classic OMNIBUS design, using F4 MCU controls OSD over SPI bus, compare the first version, we added BMP280 as barometer and SD Card supports.?OSD Configuration has been incl. in Betaflight GUI.?FC?incl. 5V1A BEC on board(3-6s) and 1x 8V BEC for Camera?MPU6000 at SPI bus, Ext, SPI for damped gyro ?Use fireworks v2 firmware, in?CLI,?set?gyro_to_use?=?SECOND
?New version with 8PIN Sh1.0 Socket, could be much easier connect to our 4in1 ESC by one cable.On v5, we added jumpers for Current source select, please?read the manual and set the jumper?before using the FC.
STM32 F405 MCU, Runs Betaflight 3.0 firmware
SBUS/PPM input (Pinheaders)
6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)
Only 36x36mm, mount holes 30.5x30.5mm
INCL. BARO BMP280
SPI Sensor MPU6000
Flash
Brushless ESC
32bit ESC with BLHELI32 firmware
Supports 3-6S lipo input
4PWM input
Voltage output (VBAT)
Supports Oneshot / Multishot / Dshot PWM
Mounting holes 30.5x30.5mm
Supports damped light
NO BEC
Supports?DSHOT?1200, BLHELI32 firmware.
Added more CAPS to reduce power noise.
1 x Flight Cotnroller
1 x Brushless ESC
1 x?3CM 8pin cable
1 x?4CM FPC cable