Original DJI E-Port Development Kit For Matrice 350 RTK / M300 RTK / M30 / M30T / Mavic 3E / 3T
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Product code
TBD06039202
Bob Shop ID
595907854
1. XT30 VCC power supply:
- Matrice Mavic 3E/3T: 12-17.6V 4A
- MMatrice M30 Series: 19.2-26.1V 4A
- Matrice M300 RTK: 24V 4A
- Matrice 350 RTK: 24V 4A
- XT30 12V power supply: 12V 4A
- XT30 5V power supply: 5V 4A
2. The E-Port of the aircraft can be converted into a variety of standard hardware interfaces, including XT30 power output interface, USB 2.0 interface, UART/PPS signal interface, which is convenient for developers to connect hardware devices and SDK development and debugging
3. Adaptable products: DJI Matrice 350 RTK, Matrice M300 RTK, Matrice M30/M30T, Mavic 3E/3T
4. Packing list:
- E-Port adapter board x 1
- Pin protection plug x 1
- E-Port coaxial cable (15cm) x 1
- XT30 to USB-C power cable (30cm) x 1
- XT30 to DC5.5 power cord (30cm) x 1
5. Warm tips:
- When using the adapter board alone for debugging, be sure to place the adapter board in a suitable position to avoid contact between the adapter board and the aircraft arm, or it may cause a short circuit
- If you need to integrate the adapter board into a finished load, be sure to design a heat sink and metal case
- If you find any sparks, smoke, burning odor or other abnormalities after powering up the adapter, please turn off the power immediately
- If all three XT30 power outputs are used at the same time, the total output power should be less than the maximum output power of one channel of the aircraft. Be sure to develop loads within the limits of the output specifications
6. Adapter plate size: 55 x 40 x 9 mm
- Matrice Mavic 3E/3T: 12-17.6V 4A
- MMatrice M30 Series: 19.2-26.1V 4A
- Matrice M300 RTK: 24V 4A
- Matrice 350 RTK: 24V 4A
- XT30 12V power supply: 12V 4A
- XT30 5V power supply: 5V 4A
2. The E-Port of the aircraft can be converted into a variety of standard hardware interfaces, including XT30 power output interface, USB 2.0 interface, UART/PPS signal interface, which is convenient for developers to connect hardware devices and SDK development and debugging
3. Adaptable products: DJI Matrice 350 RTK, Matrice M300 RTK, Matrice M30/M30T, Mavic 3E/3T
4. Packing list:
- E-Port adapter board x 1
- Pin protection plug x 1
- E-Port coaxial cable (15cm) x 1
- XT30 to USB-C power cable (30cm) x 1
- XT30 to DC5.5 power cord (30cm) x 1
5. Warm tips:
- When using the adapter board alone for debugging, be sure to place the adapter board in a suitable position to avoid contact between the adapter board and the aircraft arm, or it may cause a short circuit
- If you need to integrate the adapter board into a finished load, be sure to design a heat sink and metal case
- If you find any sparks, smoke, burning odor or other abnormalities after powering up the adapter, please turn off the power immediately
- If all three XT30 power outputs are used at the same time, the total output power should be less than the maximum output power of one channel of the aircraft. Be sure to develop loads within the limits of the output specifications
6. Adapter plate size: 55 x 40 x 9 mm