PE4302 Digital RF Step Attenuator Module DC 4GHZ 0-31.5DB 0.5dB High Linearity
New
Shipping
Standard courier shipping from R30
R30 Standard shipping using one of our trusted couriers applies to most areas in South Africa. Some areas may attract a R30 surcharge. This will be calculated at checkout if applicable.
Check my rate
Check my rate
Ready to ship in
The seller has indicated that they will usually have this item
ready to ship within 15 business days. Shipping time depends on your delivery address. The most
accurate delivery time will be calculated at checkout, but in
general, the following shipping times apply:
Standard Delivery
| Main centres: | 1-3 business days |
| Regional areas: | 3-4 business days |
| Remote areas: | 3-5 business days |
Returns
Get it now, pay later
Seller
Buyer Protection
Product details
Condition
New
Location
International
Bob Shop ID
615099022
Features:?
The PE4302 is a high linearity, 6-bit RF Digital Step Attenuator (DSA) covering a 31.5 dB attenuation range in 0.5 dB steps.
This 50-ohm RF DSA provides both parallel and serial CMOS control interface operates on a single 3-volt supply and maintains
high attenuation accuracy over frequency and temperature. It also has a unique control interface that allows the user to select an
initial attenuation state at power-up. Having shielding shell and anti-reverse protection diode.
Technical indicators:
?
1, the supply voltage: 5V DC (typical current value 5mA)
2, programmable gain attenuation range: 0 to 31.5dB, step 0.5dB, input and output impedance: 50 ohms
3, the module supports parallel and serial mode and boot status selection function
4, bandwidth: 1MHz to 4GHz (different attenuation values are different)
5, with a metal shell shield
Different?mode configuration:
1, Serial?mode configuration:Disconnect?J5 J7 J6?shorted?J4
Three-wire serial?modePin?are: GND DATA CLK LE 3.3V
2, Parallel?C0.5-C16?control?mode configuration:Disconnect?J4 J7?J5 J6?shorting
3, Parallel?PUP?control?mode configuration:Disconnect?J4 J5?shorted?J7 J6
?
Package included:
?
1 x?PE4302 Digital RF Step Attenuator Module
The PE4302 is a high linearity, 6-bit RF Digital Step Attenuator (DSA) covering a 31.5 dB attenuation range in 0.5 dB steps.
This 50-ohm RF DSA provides both parallel and serial CMOS control interface operates on a single 3-volt supply and maintains
high attenuation accuracy over frequency and temperature. It also has a unique control interface that allows the user to select an
initial attenuation state at power-up. Having shielding shell and anti-reverse protection diode.
Technical indicators:
?
1, the supply voltage: 5V DC (typical current value 5mA)
2, programmable gain attenuation range: 0 to 31.5dB, step 0.5dB, input and output impedance: 50 ohms
3, the module supports parallel and serial mode and boot status selection function
4, bandwidth: 1MHz to 4GHz (different attenuation values are different)
5, with a metal shell shield
Different?mode configuration:
1, Serial?mode configuration:Disconnect?J5 J7 J6?shorted?J4
Three-wire serial?modePin?are: GND DATA CLK LE 3.3V
2, Parallel?C0.5-C16?control?mode configuration:Disconnect?J4 J7?J5 J6?shorting
3, Parallel?PUP?control?mode configuration:Disconnect?J4 J5?shorted?J7 J6
?
Package included:
?
1 x?PE4302 Digital RF Step Attenuator Module